AT90SCR100 datasheet(107/433 Pages) ATMEL

107 / 433 page

107

TPR0327AY–SMS–30Jan09

AT90SCR100

generate a PWM or variable frequency output on the Output Compare pin (OCR1A/B). See

“Output Compare Units” on page 114. The compare match event will also set the Compare

Match Flag (OCF1A/B) which can be used to generate an Output Compare interrupt request.

The Input Capture Register can capture the Timer/Counter value at a given external (edge trig-

gered) event on either the Input Capture pin (ICP1). The Input Capture unit includes a digital

filtering unit (Noise Canceler) for reducing the chance of capturing noise spikes.

The TOP value, or maximum Timer/Counter value, can in some modes of operation be defined

by either the OCR1A Register, the ICR1 Register, or by a set of fixed values. When using

OCR1A as TOP value in a PWM mode, the OCR1A Register can not be used for generating a

PWM output. However, the TOP value will in this case be double buffered allowing the TOP

value to be changed in run time. If a fixed TOP value is required, the ICR1 Register can be used

as an alternative, freeing the OCR1A to be used as PWM output.

13.2.1.2

Definitions

Most register and bit references in this section are written in general form. A lower case “x”

replaces the Output Compare unit channel.

The following definitions are used extensively throughout the section:

13.2.2

Accessing 16-bit Registers

The TCNT1, OCR1A/B, and ICR1 are 16-bit registers that can be accessed by the AVR CPU via

the 8-bit data bus. The 16-bit register must be byte accessed using two read or write operations.

Each 16-bit timer has a single 8-bit register for temporary storage of the high byte of the 16-bit

access. The same temporary register is shared between all 16-bit registers within each 16-bit

timer. Accessing the low byte triggers the 16-bit read or write operation. When the low byte of a

16-bit register is written by the CPU, the high byte stored in the temporary register, and the low

byte written are both copied into the 16-bit register in the same clock cycle. When the low byte of

a 16-bit register is read by the CPU, the high byte of the 16-bit register is copied into the tempo-

rary register in the same clock cycle as the low byte is read.

Not all 16-bit accesses uses the temporary register for the high byte. Reading the OCR1A/B 16-

bit registers does not involve using the temporary register.

To do a 16-bit write, the high byte must be written before the low byte. For a 16-bit read, the low

byte must be read before the high byte.

The following code examples show how to access the 16-bit Timer Registers assuming that no

interrupts updates the temporary register. The same principle can be used directly for accessing

the OCR1A/B and ICR1 Registers. Note that when using “C”, the compiler handles the 16-bit

access.

Table 13-10.

Definitions

BOTTOM

The counter reaches the BOTTOM when it becomes 0x0000.

MAX

The counter reaches its MAXimum when it becomes 0xFFFF (decimal 65535).

TOP

The counter reaches the TOP when it becomes equal to the highest value in the count

sequence. The TOP value can be assigned to be one of the fixed values: 0x00FF, 0x01FF,

or 0x03FF, or to the value stored in the OCR1A or ICR1 Register. The assignment is

dependent of the mode of operation.

AT90SCR100 Datasheet(PDF) 107 Page - ATMEL Corporation

AT90SCR100 Datasheet(HTML) 107 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL