PSD813F2 datasheet(15/128 Pages) STMICROELECTRONICS

15 / 128 page

PSD8XXFX

Pin description

Doc ID 7833 Rev 7

15/128

Pin description

Table 3.

PLCC52 pin description (1)

Pin name

Type

Description

ADIO0-7

30-37

I/O

This is the lower Address/Data port. Connect your MCU address or address/data bus

according to the following rules:

If your MCU has a multiplexed address/data bus where the data is multiplexed with the

lower address bits, connect AD0-AD7 to this port.

If your MCU does not have a multiplexed address/data bus, or you are using an 80C251

in page mode, connect A0-A7 to this port.

If you are using an 80C51XA in burst mode, connect A4/D0 through A11/D7 to this port.

ALE or AS latches the address. The PSD drives data out only if the READ signal is

active and one of the PSD functional blocks was selected. The addresses on this port

are passed to the PLDs.

ADIO8-15

39-46

I/O

This is the upper Address/Data port. Connect your MCU address or address/data bus

according to the following rules:

If your MCU has a multiplexed address/data bus where the data is multiplexed with the

lower address bits, connect A8-A15 to this port.

If your MCU does not have a multiplexed address/data bus, connect A8-A15 to this port.

If you are using an 80C251 in page mode, connect AD8-AD15 to this port.

If you are using an 80C51XA in burst mode, connect A12/D8 through A19/D15 to this

port.

ALE or AS latches the address. The PSD drives data out only if the READ signal is

active and one of the PSD functional blocks was selected. The addresses on this port

are passed to the PLDs.

CNTL0

The following control signals can be connected to this port, based on your MCU:

WR – active low Write Strobe input.

R_W – active high READ/active low write input.

This port is connected to the PLDs. Therefore, these signals can be used in decode

and other logic equations.

CNTL1

The following control signals can be connected to this port, based on your MCU:

RD – active low Read Strobe input.

E – E clock input.

DS – active low Data Strobe input.

PSEN – connect PSEN to this port when it is being used as an active low READ signal.

For example, when the 80C251 outputs more than 16 address bits, PSEN is actually

the READ signal.

This port is connected to the PLDs. Therefore, these signals can be used in decode

and other logic equations.

CNTL2

This port can be used to input the PSEN (Program Select Enable) signal from any MCU

that uses this signal for code exclusively. If your MCU does not output a Program Select

Enable signal, this port can be used as a generic input. This port is connected to the

PLDs.

Reset

Resets I/O ports, PLD macrocells and some of the Configuration registers. Must be low

at Power-up.

Obsolete

Product(s)

- Obsolete

Product(s)

PSD813F2 Datasheet(PDF) 15 Page - STMicroelectronics

PSD813F2 Datasheet(HTML) 15 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL