CS5336 datasheet(10/34 Pages) CIRRUS

10 / 34 page

Certain serial modes align well with various inter-

face requirements. A CS5339 in MASTER mode,

with an inverted L/R signal, generates I

(Philips) compatible timing. A CS5336 in MAS-

TER mode, using FSYNC, interfaces well with a

Motorola DSP56000. A CS5336 in SLAVE mode

emulates a CS5326 style interface, and also links

up to a DSP56000 in network mode.

Analog Connections

The analog inputs are presented to the modulators

via the AINR and AINL pins. The analog input

signal range is determined by the internal voltage

reference value, which is typically -3.68 volts.

The input signal range therefore is typically

± 3.68 volts.

The ADC samples the analog inputs at

3.072 MHz for a 12.288 MHz ICLKD (CMODE

low). For the CS5336, the digital filter rejects all

noise between 26 kHz and (3.072 MHz-26 kHz).

For the CS5338 and CS5339, the digital filter re-

jects

all

no ise

between

kHz

and

(3.072 MHz-28 kHz). However, the filter will not

reject frequencies right around 3.072 MHz (and

multiples of 3.072 MHz). Most audio signals do

not have significant energy at 3.072 MHz. Never-

theless, a 51

Ω resistor in series with the analog

input, and a 10 nF NPO or COG capacitor to

ground will attenuate any noise energy at 3.072

MHz, in addition to providing the optimum

source impedance for the modulators. The use of

capacitors which have a large voltage coefficient

(such as general purpose ceramics) should be

avoided since these can degrade signal linearity. If

active circuitry precedes the ADC, it is recom-

mended that the above RC filter is placed between

the active circuitry and the AINR and AINL pins.

The above example frequencies scale linearly with

output word rate.

The on-chip voltage reference output is brought

out to the VREF pin. A 10

µF electrolytic capaci-

tor in parallel with a 0.1

µF ceramic capacitor

attached to this pin eliminates the effects of high

frequency noise. Note the negative value of VREF

when using polarized capacitors. No load current

may be taken from the VREF output pin.

The analog input level used as zero during the

offset calibration period (described later) is input

on the ZEROL and ZEROR pins. Typically, these

pins are directly attached to AGND. For the ulti-

mate in offset nulling, networks can be attached to

ZEROR and ZEROL whose impedances match

the impedances present on AINL and AINR.

Power-Down and Offset Calibration

The ADC has a power-down mode wherein typi-

cal consumption drops to 150

µW. In addition,

exiting the power-down state initiates an offset

calibration procedure.

APD and DPD are the analog and digital power-

down pins. When high, they place the analog and

digital sections in the power-down mode.

Bring-

ing these pins low takes the part out of

power-down mode. DPD going low initiates a

calibration cycle. If not using the power down

feature, APD should be tied to AGND. When us-

ing the power down feature, DPD and APD may

be tied together if the capacitor on VREF is not

DCAL

DPD

Cal Period

(4096 x L/R clocks)

(85.33 ms @ 48kHz)

Filter Delay Time

(~40 L/R periods)

(~2 ms @ 48 kHz)

Normal Operation

Figure 6. Initial Calibration Cycle Timing

CS5336, CS5338, CS5339

3-48

DS23F1

CS5336 Datasheet(PDF) 10 Page - Cirrus Logic

CS5336 Datasheet(HTML) 10 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Datasheet Download

Link URL