TMS320VC5416 datasheet(32/98 Pages) TI

32 / 98 page

www.ti.com

3.9

Hardware Timer

3.10

Clock Generator

TMS320VC5416

Fixed-Point Digital Signal Processor

SPRS095O – MARCH 1999 – REVISED JANUARY 2005

R/W

LEGEND: R = Read, W = Write, n = value present after reset

Figure 3-12. Pin Control Register (PCR)

The selection of sample rate input clock is made by the combination of the CLKSM (bit 13 in SRGR2) bit

value and the SCLKME bit value as shown in Table 3-7.

Table 3-7. Sample Rate Input Clock Selection

SCLKME

CLKSM

SAMPLE RATE CLOCK MODE

Reserved (CLKS pin unavailable)

CPU clock

BCLKR

BCLKX

When the SCLKME bit is cleared to 0, the CLKSM bit is used, as before, to select either the CPU clock or

the CLKS pin (not bonded out on the device package) as the sample rate input clock. Setting the

SCLKME bit to 1 enables the CLKSM bit to select between the BCLKR pin or BCLKX pin for the sample

rate input clock.

When either the BCLKR or CLKX is configured this way, the output buffer for the selected pin is

automatically disabled. For example, with SCLKME = 1 and CLKSM = 0, the BCLKR pin is configured as

the input of the sample rate generator. Both the transmitter and receiver circuits can be synchronized to

the sample rate generator output by setting the CLKXM and CLKRM bits of the pin configuration register

(PCR) to 1. Note that the sample rate generator output will only be driven on the BCLKX pin since the

BCLKR output buffer is automatically disabled.

The McBSP is fully static and operates at arbitrary low clock frequencies. For maximum operating

frequency, see Section 5.5.10.

The device features a 16-bit timing circuit with a 4-bit prescaler. The timer counter is decremented by one

every CLKOUT cycle. Each time the counter decrements to 0, a timer interrupt is generated. The timer

can be stopped, restarted, reset, or disabled by specific status bits.

The clock generator provides clocks to the device, and consists of a phase-locked loop (PLL) circuit. The

clock generator requires a reference clock input, which can be provided from an external clock source.

The reference clock input is then divided by two (DIV mode) to generate clocks for the device, or the PLL

circuit can be used (PLL mode) to generate the device clock by multiplying the reference clock frequency

by a scale factor, allowing use of a clock source with a lower frequency than that of the CPU. The PLL is

an adaptive circuit that, once synchronized, locks onto and tracks an input clock signal.

When the PLL is initially started, it enters a transitional mode during which the PLL acquires lock with the

input signal. Once the PLL is locked, it continues to track and maintain synchronization with the input

signal. Then, other internal clock circuitry allows the synthesis of new clock frequencies for use as master

clock for the device.

Functional Overview

TMS320VC5416 Datasheet(PDF) 32 Page - Texas Instruments

TMS320VC5416 Datasheet(HTML) 32 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98

Datasheet Download

Link URL