PC87303 datasheet(88/114 Pages) NSC

88 / 114 page

90 Keyboard Controller and Real-Time Clock (Continued)

Program Status Word Register (PSW)

This 8-bit register holds the program execution status The

bit definition of the PSW register is shown in

Figure 9-6

rsv

SP k20l

bit

2-0

FIGURE 9-6 PSW Register Bits

Bit 7

CY Carry flag of the accumulator

Bit 6

AC Auxiliary Carry flag of the accumulator ie

carry from bit 3 to 4 of the ALU

Bit 5

F0 Flag 0 A general purpose software flag

Bit 4

BS The current active register bank

0 e bank 0 1 e bank 1

Bit 3

Reserved User should not change its power-up

value

Bits 2-0

Stack Pointer 3-bit Stack Pointer for 8-level stack

When the CPU performs a subroutine call or interrupt call

the PC and the upper 4 bits of the PSW are pushed into the

stack Upon return the PSW can be restored in option If a

RETR Return instruction is executed PSW is restored PSW

is not restored if an RET Return instruction is executed See

Figure 9-5

914 IO Interface

The keyboard controller of the PC87303 provides 16 gener-

al purpose IO lines two open-collector output lines and

two input lines as shown in the Functional Block Diagram in

Figure 9-1

General Purpose IO

The 16 general purpose IO lines P10 – P17 and P20 – P27

are mapped to Port 1 and Port 2 respectively These IO

lines are quasi-bidirectional because the output buffer can-

not be turned off even if the IO line is intended for input

Whena0is written to an IO line it behaves like an output

Whena1is written to an IO line it behaves like an input

On reset all IO lines are inputs

Figure 9-7 illustrates the structure of the IO line Q1 and Q2

are the normal output transistors When the IO line is in-

tended for output 0 is written into the flip-flop which latch-

es and Q2 turns on When 1 is written Q1 turns on briefly

because it is gated by a short port-write pulse also Q1

charges up the pad to near VCC and then turns off An ac-

tive pull-up transistor Q3 turns on also but it provides a

large pull-up resistance because it is a weak transistor At

this stage the IO line can be used as input a low imped-

ance low voltage can override the pin and the input buffer

reads a low level input If the pin is driven high or undriven a

high level is read Therefore to use a port pin as input a

logic 1 must first be written to it When the keyboard control-

ler is reset all port lines will be initialized to logic 1

Because Q1 turns on momentarily when a write to the port

is performed there is potential for a current surge A series

resistor connected to those port lines used as inputs is rec-

ommended to limit the potential surge

(Figure 9-8)

TLC12074 – 42

FIGURE 9-7 Active Pull-Up IO Port Structure

R current limiting resistor

A small-value series current limiting

resistor is recommended when

PORT PINS are used as inputs

TLC12074 – 43

FIGURE 9-8 Using Port Pins as Inputs

PC87303 Datasheet(PDF) 88 Page - National Semiconductor (TI)

PC87303 Datasheet(HTML) 88 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL