ADP5360ACBZ-2-R7 datasheet(51/60 Pages) AD

51 / 60 page

Data Sheet

ADP5360

Rev. 0 | Page 51 of 60

Table 65. PGOOD_STATUS Register, Address 0x2F Bit Descriptions

Bit(s)

Bit Name

Access Default

Description

[7:6]

Reserved

Not applicable

Reserved

MR_PRESS

Not applicable

When high, this bit indicates that the MR pin is pulled to low after tDG.

CHG_CMPLT

Not applicable

This bit shows battery charge complete.

0 = the charger is not in charge complete status.

1 = the charger is in charge complete status.

VBUSOK

Not applicable

This bit shows the real-time status of the VBUS pin voltage.

0 = the voltage of the VBUS pin is lower than VVBUS_OK or higher than VVBUS_OV.

1 = the voltage of the VBUS pin is higher than VVBUS_OK and lower than VVBUS_OV.

BATOK

Not applicable

This bit shows the real-time status of the battery voltage. This bit is only active when

the fuel gauge function is enabled.

0 = battery voltage is less than VWEAK.

1 = battery voltage is more than VWEAK.

VOUT2OK

Not applicable

This bit shows real-time power good status for the buck boost regulator. This bit is only

effective in buck boost standalone fixed output mode.

0 = buck boost regulator power-good status is low.

1 = buck boost regulator power-good status is high.

VOUT1OK

Not applicable

This bit shows real-time power-good status for the buck regulator. This bit is not

effective if the buck is configured as load switch mode.

0 = buck power-good status is low.

1 = buck power-good status is high.

Table 66. PGOOD1_MASK Register, Address 0x30 Bit Descriptions

Bit(s)

Bit Name

Access

Default

Description

PG1_REV

R/W

Factory set

This bit configures the active low output of the PGOOD1 pin.

0 = disable active low.

1 = enable active low.

[6:5]

Reserved

Not applicable

Reserved

CHGCMPLT_MASK1

R/W

This bit configures the external PGOOD1 pin.

0 = does not send the output charger complete signal to the external PGOOD1 pin.

1 = sends the output charger complete signal to the external PGOOD1 pin.

VBUSOK_MASK1

R/W

Factory set

This bit configures the external PGOOD1 pin.

0 = does not send the outputVBUS voltage status signal to the external PGOOD1 pin.

1 = sends the output VBUS voltage status signal to the external PGOOD1 pin.

BATOK_MASK1

R/W

This bit configures the external PGOOD1 pin.

0 = does not send the output battery voltage okay signal to the external PGOOD1 pin.

1 = sends the output battery voltage okay signal to the external PGOOD1 pin.

VOUT2OK_MASK1

R/W

This bit configures the external PGOOD1 pin for buck boost output.

0 = does not send the output buck boost PGOOD signal to the external PGOOD1 pin.

1 = sends the output buck boost PGOOD signal to the external PGOOD1 pin.

VOUT1OK_MASK1

R/W

Factory set

This bit configures the external PGOOD1 pin. This bit is not effective if the buck

is configured in load switch mode.

0 = does not send the output buck PGOOD signal to the external PGOOD1 pin.

1 = sends the output buck PGOOD signal to the external PGOOD1 pin.

ADP5360ACBZ-2-R7 Datasheet(PDF) 51 Page - Analog Devices

ADP5360ACBZ-2-R7 Datasheet(HTML) 51 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

Datasheet Download

Link URL