AMPL138ZCE3 datasheet(44/268 Pages) TI

44 / 268 page

3.9.10

Enhanced Pulse Width Modulators (eHRPWM)

OMAP-L138 Low-Power Applications Processor

SPRS586A – JUNE 2009 – REVISED AUGUST 2009

www.ti.com

Table 3-13. Enhanced Pulse Width Modulator (eHRPWM) Terminal Functions

SIGNAL

POWER

TYPE(1)

PULL(2)

DESCRIPTION

GROUP(3)

NAME

NO.

eHRPWM0

eHRPWM0 A output

SPI0_CLK / EPWM0A / GP1[8] / MII_RXCLK

D19

I/O

CP[7]

(with high-resolution)

SPI0_ENA / EPWM0B / PRU0_R30[6] / MII_RXDV

C17

I/O

CP[7]

eHRPWM0 B output

AXR15 / EPWM0TZ[0] / ECAP2_APWM2 / GP0[7]

I/O

CP[1]

eHRPWM0 trip zone input

SPI0_SOMI /EPWMSYNCI / GP8[6] / MII_RXER

C16

I/O

CP[7]

eHRPWM0 sync input

SPI0_SIMO /EPWMSYNCO / GP8[5] / MII_CRS

C18

I/O

CP[7]

eHRPWM0 sync output

eHRPWM1

SPI1_SCS[1] / EPWM1A / PRU0_R30[7] / GP2[15] /

eHRPWM1 A output

F18

I/O

CP[14]

TM64P2_IN12

(with high-resolution)

SPI1_SCS[0] / EPWM1B/ PRU0_R30[8] / GP2[14] /

E19

I/O

CP[14]

eHRPWM1 B output

TM64P3_IN12

AXR7 / EPWM1TZ[0] / PRU0_R30[17] / GP1[15] /

I/O

CP[4]

eHRPWM1 trip zone input

PRU0_R31[7]

(1)

I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.

Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name

highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured

function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different

types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.

(2)

IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using

the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the

device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a

pull-up, an external pull-up can be used.

(3)

This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can

be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of

power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power

supply DVDD3318_C.

Device Overview

Submit Documentation Feedback

AMPL138ZCE3 Datasheet(PDF) 44 Page - Texas Instruments

AMPL138ZCE3 Datasheet(HTML) 44 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL