OR2C04A datasheet(25/192 Pages) ETC

25 / 192 page

Lucent Technologies Inc.

Data Sheet

June 1999

ORCA Series 2 FPGAs

Programmable Input/Output Cells

The programmable input/output cells (PICs) are

located along the perimeter of the device. Each PIC

interfaces to four bond pads and contains the neces-

sary routing resources to provide an interface between

I/O pads and the PLCs. Each PIC is composed of input

buffers, output buffers, and routing resources as

described below. Table 6 provides an overview of the

programmable functions in an I/O cell. A is a simplified

diagram of the functionality of the OR2CxxA series I/O

cells, while B is a simplified functional diagram of the

OR2TxxA and OR2TxxB series I/O cells.

Table 6. Input/Output Cell Options

Inputs

Each I/O can be configured to be either an input, an

output, or bidirectional I/O. Inputs for the OR2CxxA can

be configured as either TTL or CMOS compatible. The

I/O for the OR2TxxA and OR2TxxB series devices are

5 V tolerant, and will be described in a later section of

this data sheet. Pull-up or pull-down resistors are avail-

able on inputs to minimize power consumption.

To allow zero hold time to PLC latches/FFs, the input

signal can be delayed. When enabled, this delay affects

the input signal driven to general routing, but does not

affect the clock input or the input lines that drive the

TRIDI buffers (used to drive onto XL, XH, BIDI, and

BIDIH lines).

A fast path from the input buffer to the clock lines is

also provided. Any one of the four I/O pads on any PIC

can be used to drive the clock line generated in that

PIC. This path cannot be delayed.

To reduce the time required to input a signal into the

FPGA, a dedicated path (PDIN) from the I/O pads to

the PFU flip-flops is provided. Like general input sig-

nals, this signal can be configured as normal or

delayed. The delayed direct input can be selected inde-

pendently from the delayed general input.

Inputs should have transition times of less than 500 ns

and should not be left floating. If an input can float, a

pull-up or pull-down should be enabled. Floating inputs

increase power consumption, produce oscillations, and

increase system noise. The OR2CxxA inputs have a

typical hysteresis of approximately 280 mV (200 mV for

the OR2TxxA and OR2TxxB) to reduce sensitivity to

input noise. The PIC contains input circuitry which pro-

vides protection against latch-up and electrostatic dis-

charge.

Input

Option

Input Levels

TTL/CMOS (OR2CxxA only)

5 V PCI compliant (OR2CxxA only)

3.3 V PCI compliant (OR2TxxA only)

3.3 V and 5 V PCI compliant

(OR2TxxB only)

Input Speed

Fast/Delayed

Float Value

Pull-up/Pull-down/None

Direct-in to FF

Fast/Delayed

Output

Option

Output Drive

12 mA/6 mA or 6 mA/3 mA

Output Speed

Fast/Slewlim/Sinklim

Output Source

FF Direct-out/General Routing

Output Sense

Active-high/-low

3-State Sense

Active-high/-low (3-state)

OR2C04A Datasheet(PDF) 25 Page - List of Unclassifed Manufacturers

OR2C04A Datasheet(HTML) 25 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL