LPC47M192 datasheet(69/228 Pages) SMSC

69 / 228 page

SMSC DS – LPC47M192

Page 69

Rev. 03/30/05

DATASHEET

Bit 4

Even Parity Select bit. When bit 3 is a logic “1” and bit 4 is a logic “0”, an odd number of logic “1”’s is transmitted or

checked in the data word bits and the parity bit. When bit 3 is a logic “1” and bit 4 is a logic “1” an even number of

bits is transmitted and checked.

Bit 5

This bit is the Stick Parity bit. When parity is enabled it is used in conjunction with bit 4 to select Mark or Space

Parity. When LCR bits 3, 4 and 5 are 1 the Parity bit is transmitted and checked as a 0 (Space Parity). If bits 3 and 5

are 1 and bit 4 is a 0, then the Parity bit is transmitted and checked as 1 (Mark Parity). If bit 5 is 0 Stick Parity is

disabled.

Bit 6

Set Break Control bit. When bit 6 is a logic “1”, the transmit data output (TXD) is forced to the Spacing or logic “0”

state and remains there (until reset by a low level bit 6) regardless of other transmitter activity. This feature enables

the Serial Port to alert a terminal in a communications system.

Bit 7

Divisor Latch Access bit (DLAB). It must be set high (logic “1”) to access the Divisor Latches of the Baud Rate

Generator during read or write operations. It must be set low (logic “0”) to access the Receiver Buffer Register, the

Transmitter Holding Register, or the Interrupt Enable Register.

MODEM CONTROL REGISTER (MCR)

Address Offset = 4H, DLAB = X, READ/WRITE

This 8 bit register controls the interface with the MODEM or data set (or device emulating a MODEM). The contents

of the MODEM control register are described below.

Bit 0

This bit controls the Data Terminal Ready (nDTR) output. When bit 0 is set to a logic “1”, the nDTR output is forced

to a logic “0”. When bit 0 is a logic “0”, the nDTR output is forced to a logic “1”.

Bit 1

This bit controls the Request To Send (nRTS) output. Bit 1 affects the nRTS output in a manner identical to that

described above for bit 0.

Bit 2

This bit controls the Output 1 (OUT1) bit. This bit does not have an output pin and can only be read or written by the

CPU.

Bit 3

Output 2 (OUT2). This bit is used to enable an UART interrupt. When OUT2 is a logic "0", the serial port interrupt

output is forced to a high impedance state - disabled. When OUT2 is a logic "1", the serial port interrupt outputs are

enabled.

Bit 4

This bit provides the loopback feature for diagnostic testing of the Serial Port. When bit 4 is set to logic “1”, the

following occur:

The TXD is set to the Marking State(logic “1”).

The receiver Serial Input (RXD) is disconnected.

The output of the Transmitter Shift Register is “looped back” into the Receiver Shift Register input.

All MODEM Control inputs (nCTS, nDSR, nRI and nDCD) are disconnected.

The four MODEM Control outputs (nDTR, nRTS, OUT1 and OUT2) are internally connected to the four

MODEM Control inputs (nDSR, nCTS, RI, DCD).

The Modem Control output pins are forced inactive high.

Data that is transmitted is immediately received.

This feature allows the processor to verify the transmit and receive data paths of the Serial Port. In the diagnostic

mode, the receiver and the transmitter interrupts are fully operational. The MODEM Control Interrupts are also

LPC47M192 Datasheet(PDF) 69 Page - SMSC Corporation

LPC47M192 Datasheet(HTML) 69 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL