ADS8328IBPW datasheet(24/50 Pages) TI

24 / 50 page

ADS8327

ADS8328

SLAS415E

– APRIL 2006 – REVISED JANUARY 2011

www.ti.com

Manual Channel Select Mode

The conversion cycle starts with selecting an acquisition channel by writing a channel number to the command

Auto Channel Select Mode

Channel selection can also be done automatically if auto channel select mode is enabled. This is the default

channel select mode. The dual channel converter, ADS8328, has a built-in 2-to-1 MUX. If the device is

programmed for auto channel select mode then signals from channel 0 and channel 1 are acquired with a fixed

order. Channel 0 is accessed first in the next cycle after the command cycle that configured CFR_D11 to 1 for

auto channel select mode. This automatic access stops the cycle after the command cycle that sets CFR_D11 to

'0'.

Start of a Conversion

The end of acquisition or sampling instance (EOS) is the same as the start of a conversion. This is initiated by

bringing the CONVST pin low for a minimum of 40 ns. After the minimum requirement has been met, the

CONVST pin can be brought high. CONVST acts independent of FS/CS so it is possible to use one common

CONVST for applications requiring simultaneous sample/hold with multiple converters. The ADS8327/28

switches from sample to hold mode on the falling edge of the CONVST signal. The ADS8327/28 requires 18

conversion clock (CCLK) edges to complete a conversion. The conversion time is equivalent to 1500 ns with a

12-MHz internal clock. The minimum time between two consecutive CONVST signals is 21 CCLKs.

A conversion can also be initiated without using CONVST if it is so programmed (CFR_D9 = 0). When the

converter is configured as auto trigger, the next conversion is automatically started three conversion clocks

(CCLK) after the end of a conversion. These three conversion clocks (CCLK) are used as the acquisition time. In

this case the time to complete one acquisition and conversion cycle is 21 CCLKs.

Table 2. Different Types of Conversion

MODE

SELECT CHANNEL

START CONVERSION

Auto Channel Select(1)

Auto Trigger

Automatic No need to write channel number to the CMR. Use internal sequencer for the

Start a conversion based on the conversion

ADS8328.

clock CCLK.

Manual Channel Select

Manual Trigger

Manual

Write the channel number to the CMR.

Start a conversion with CONVST.

(1)

Auto channel select should be used with auto trigger and also with the TAG bit enabled.

Status Output EOC/INT

When the status pin is programmed as EOC and the polarity is set as active low, the pin works in the following

manner: The EOC output goes LOW immediately following CONVST going LOW when manual trigger is

programmed. EOC stays LOW throughout the conversion process and returns to HIGH when the conversion has

ended. The EOC output goes low for three conversion clocks (CCLK) after the previous rising edge of EOC, if

auto trigger is programmed.

This status pin is programmable. It can be used as an EOC output (CFR.D[7:6] = 1, 1) where the low time is

equal to the conversion time. This status pin can be used as INT. (CFR.D[7:6] = 1, 0) which is set LOW at the

end of a conversion is brought to HIGH (cleared) by the next read cycle. The polarity of this pin, used as either

function (EOC or INT), is programmable through CFR_D7.

Submit Documentation Feedback

Product Folder Link(s): ADS8327 ADS8328

ADS8328IBPW Datasheet(PDF) 24 Page - Texas Instruments

ADS8328IBPW Datasheet(HTML) 24 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

Datasheet Download

Link URL