| Electronic Components Datasheet Search |
|
HMC832LP6GETR Datasheet(PDF) 45 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
HMC832LP6GETR Datasheet(HTML) 45 Page - Analog Devices |
|
45 / 49 page ![]() HMC832 Data Sheet VCO OUTPUT DIVIDER REGISTER This is a write only register. Note that to write 0_1111_1110 into VCO_REG 0x02 VCO subsystem (VCO_ID = 000b), and set the VCO output divider to divide by 62, the following needs to be written to Register 0x05 = 0_1111_1110, 0010, 000 b. Register 0x05[2:0] = 000; Subsystem ID 0 Register 0x05[6:3] = 0010; VCO Register Address 2d. Register 0x05[16:7] = 0_1111_1110; divide by 62, maximum output RF gain. Table 33. VCO_REG 0x02 VCO Output Divider Bit Type Name Width Default Description 5:0 W RF divide ratio 6 1 0: mutes the output when VCO_REG 0x03[8:7] = 0d 1: fo 2: fo/2 3: invalid, defaults to 2 4: fo/4 5: invalid, defaults to 4 6: fo/6 … 60: fo/60 61: invalid, defaults to 60 62: fo/62 > 62 invalid, defaults to 62 8:6 W Reserved 3 0 Reserved VCO CONFIGURATION REGISTER The VCO configuration register is a write only register. Table 34. VCO_REG 0x03 Configuration Bit Type Name Width Default Description 1:0 W Programmable performance mode 2 2 Selects output noise floor performance level at a cost of increased current consumption. 01: low current consumption mode. 11: high performance mode. Other states (00 and 10) not supported. 2 W RF_N output enable 1 0 Enables the output on RF_N pin. Required for differential operation, or single-ended output on the RF_N pin. 3 W RF_P output enable 1 0 Enables the output on RF_P pin. Required for differential operation, or single-ended output on the RF_P pin. 4 W Reserved 1 1 Reserved. 5 W Return loss 1 0 0: return loss = −5 dB typical (highest output power). 1: return loss = −10 dB typical. 6 W Reserved 1 0 Reserved. 8:7 W Mute mode 2 1 Defines when the mute function is enabled (the output is muted), see the VCO Output Mute Function section, and Figure 35 for more information. 00: enables mute when the divide ratio, VCO_REG 0x02[5:0] = 0. This enables the HMC832 to be backwards compatible to the HMC830 mute function. 01: during VCO calibration (see the VCO Calibration section for more details). 10: not supported. 11: mute all RF outputs (unconditional). Rev. A | Page 44 of 48 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |