FS32R274VCK2MMM datasheet(15/78 Pages) NXP

15 / 78 page

11. While determining if the operating temperature specifications are met, either the ambient temperature or junction

temperature specification can be used. It is critical that the junction temperature specification is not exceeded under any

condition.

12. Full performance means full frequency.

13. Recommended Crystal 40 MHz (ESR≤30 Ω), 8 pF load capacitance.

14. External mode can be used as differential input with EXTAL and XTAL

15. The number is 3.5 ps when SD-ADC and/or DAC is not used in the device.

4.3 Supply current characteristics

Current consumption data is given in the following table. These specifications are design

targets and are subject to change per device characterization.

Table 8. Current consumption characteristics

Symbol

Parameter

Conditions

Min Typ Max

Unit

IDD_CORE

Core current in run mode All cores at max frequency. 1.31 V. Tj = 150°C (240

MHz)

All cores at max frequency. 1.31 V. Tj = 150°C (266

MHz)

14801

16421

IDD_HV_FLA

Flash operating current

Tj = 150°C. VDD_HV_FLA = 3.6 V

403

IDD_LV_AURORA Aurora operating current

Tj = 150°C. VDD_LV_AURORA = 1.31 V. 4 TX lanes

enabled.

IDD_HV_ADC

ADC operating current

Tj = 150°C. VDD_HV_ADC = 3.6 V. 2 ADCs operating

at 80 MHz.

IDD_HV_ADCREF Reference current per

ADC4

Reference current per

temp sensor5

Tj = 150°C. VDD_HV_ADCREFx = 3.6 V. ADC operating

at 80 MHz.

1.5

0.75

IDD_HV_RAW

AFE SD and regulator

operating current

Tj = 150°C. VDD_HV_RAW = 3.6 V. SD-PLL, AFE

regulators and 4 SD enabled.

706

IDD_HV_DAC

AFE DAC operating

current

Tj = 150°C. VDD_HV_DAC = 3.6 V. DAC enabled.

IDD_HV_PMU

PMU operating current

Tj = 150°C. VDD_HV_PMU = 3.6 V. Internal

regulation enabled.

IDD_LV_DPHY

MIPICSI2 DPHY

operating current in HS-

RX mode

Tj = 150°C, VDD_LV_DPHY =1.31 V

14.9 23.2

1. Strong dependence on use case, cache usage.

2. Measured during flash read.

3. Peak Flash current measured during read while write (RWW) operation.

4. ADC0 and 1 on ADCREF0/1.

5. Temp sensor current when PMC_CTL_TD[TSx_AOUT_EN] = 1. TS0 on ADCREF0/1.

6. Typical number is approximately 10 mA per each SD-ADC enabled, 12 mA for SD-PLL and 15 mA for the AFE regulators.

General

S32R274/S32R264 Series Data Sheet, Rev. 6, 06/2021

NXP Semiconductors

FS32R274VCK2MMM Datasheet(PDF) 15 Page - NXP Semiconductors

FS32R274VCK2MMM Datasheet(HTML) 15 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78

Datasheet Download

Link URL