UCS1002-3 datasheet(48/114 Pages) MICROCHIP

48 / 114 page

UCS1002-3

DS20006852A-page 48

 2023 Microchip Technology Inc. and its subsidiaries

During Power-On Reset (POR), the default values are

stored in the registers. A POR is initiated when power

is first applied to the part and the voltage on the VDD

supply surpasses the VDD_TH level as specified in the

electrical characteristics. Any reads to undefined

registers returns 00h. Writes to undefined registers do

not have an effect.

When a bit is set, this means that the user writes a logic

‘1’ to it. When a bit is cleared, this means that the user

writes a logic ‘0’ to it.

10.1

Current Measurement Register

(Address 00h)

The Current Measurement register stores the

measured current value delivered to the portable

device (IBUS). This value is updated continuously

while the device is in the Active power state. The bit

weights are in mA and the range is from 9.76 mA to

2.5A.

This data is cleared when the device enters the Sleep

or Detect states. This data is also cleared whenever the

port power switch is turned OFF (including during

emulation or any time that VBUS is discharged).

10.2

Total Accumulated Charge

Registers

The Total Accumulated Charge registers store the total

accumulated charge delivered from the VS source to a

portable device. The bit weighting of the registers is

given in mAh. The register value is reset to 00_00h only

when the RATION_RST bit is set or if the RATION_EN

bit is cleared. This value is retained when the device

transitions out of the Active state and resumes

accumulation if the device returns to the Active state

and charge rationing is still enabled.

These registers are updated every one (1) second

while the UCS1002-3 is in the Active power state.

Whenever the value is updated, it is compared against

the target value in the Charge Rationing Threshold

registers (see Section 10.6 “Charge Rationing

Threshold Registers”).

This data is retained in the Sleep state.

47h

Custom Stimulus/Response

Pair 2 – Config 3

R/W

Sets the threshold and pull-up/pull-down

settings for Stimulus 2

00h

48h

Custom Stimulus/Response

Pair 2 – Config 4

R/W

Sets the resistor ratio for Stimulus 2

00h

49h

Custom Emulation Stimulus

3 – Config 1

R/W

Sets the stimulus and timing for

Stimulus 3

00h

4Ah

Custom Stimulus/Response

Pair 3 – Config 2

R/W

Sets the response and magnitude for

Stimulus 3

00h

4Bh

Custom Stimulus/Response

Pair 3 – Config 3

R/W

Sets the threshold and pull-up/pull-down

settings for Stimulus 3

00h

4Ch

Custom Stimulus/Response

Pair 3 – Config 4

R/W

Sets the resistor ratio for Stimulus 3

00h

50h

Applied Current Limiting

Behavior

Indicates the applied current limiting

behavior

82h

51h

Custom Current Limiting

Behavior Config

R/W

Controls the custom current limiting

behavior

82h

FDh

Product ID

Stores a fixed value that identifies each

product

4Eh

FEh

Manufacturer ID

Stores a fixed value that identifies

Microchip

5Dh

FFh

Revision

Stores a fixed value that represents the

revision number

82h

TABLE 10-1:

Address

R/W

Function

Default

Value

Page

No.

Name

Bits Address Cof. Default

Current Measurement

00h

Name

Bits Address Cof. Default

Total Accumulated

Charge High Byte

01h

00h

Total Accumulated

Charge Middle High

02h

00h

Total Accumulated

Charge Middle Low Byte

03h

00h

Total Accumulated

Charge Low Byte

04h

00h

UCS1002-3 Datasheet(PDF) 48 Page - Microchip Technology

UCS1002-3 Datasheet(HTML) 48 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL