PIC16C765SLASHP datasheet(62/158 Pages) MICROCHIP

62 / 158 page

PIC16C745/765

DS41124A-page 62

Advanced Information

10.5.1.3

USB Error Interrupt Status Register (UEIR)

The USB Error Interrupt Status Register (UEIR) con-

tains bits for each of the error sources within the USB.

Each of these bits are enabled by their respective error

enable bits (UEIE). The result is OR’ed together and

sent to the ERROR bit of the UIR register. Once an

interrupt bit has been set it must be cleared by writing

a zero to the respective interrupt bit. Each bit is set as

soon as the error condition is detected. Thus, the inter-

rupt will typically not correspond with the end of a

token being processed.

USB ERROR INTERRUPT FLAGS STATUS REGISTER (UEIR: 192h)

R/C-0

BTS_ERR OWN_ERR WRT_ERR BTO_ERR

DFN8

CRC16

CRC5

PID_ERR

R = Readable bit

C = Clearable bit

U = Unimplemented

bit, read as ‘0’

-n = Value at POR

reset

bit7

bit0

bit 7:

BTS_ERR: A bit stuff error has been detected.

bit 6:

OWN_ERR: This bit is set if the USB is processing a token and the OWN bit within the BDT is equal to 0

(signifying that the microprocessor owns the BDT and the SIE does not have access to the BDT). If process-

ing an IN TOKEN this would cause a transmit data underflow condition. Processing an OUT or SETUP

TOKEN would cause a receive data overflow condition.

bit 5:

WRT_ERR: Write Error. A write by the MCU to the USB Buffer Descriptor Table or Buffer area was unsuc-

cessful.

bit 4:

BTO_ERR: This bit is set if a bus turnaround time-out error has occurred. This USB uses a bus turnaround

timer to keep track of the amount of time elapsed between the token and data phases of a SETUP or OUT

TOKEN or the data and handshake phases of a IN TOKEN. If more than 17-bit times are counted from the

previous EOP before a transition from IDLE, a bus turnaround time-out error will occur.

bit 3:

DFN8: The data field received was not 8 bits. The USB Specification 1.1 specifies that data field must be an

integral number of bytes. If the data field was not an integral number of bytes this bit will be set.

bit 2:

CRC16: The CRC16 failed.

bit 1:

CRC5: This interrupt will detect CRC5 error in the token packets generated by the host. If set the token

packet was rejected due to a CRC5 error.

bit 0:

PID_ERR: The PID check field failed.

Note 1: Bits can only be modified when UCTRL.SUSPND = 0.

PIC16C765/P Datasheet(PDF) 62 Page - Microchip Technology

PIC16C765/P Datasheet(HTML) 62 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL