PIC16C765SLASHP datasheet(94/158 Pages) MICROCHIP

94 / 158 page

PIC16C745/765

DS41124A-page 94

Advanced Information

12.5

A/D Operation During Sleep

The A/D module can operate during SLEEP mode.

This requires that the A/D clock source be set to RC

(ADCS<1:0> = 11). When the RC clock source is

selected, the A/D module waits one instruction cycle

before starting the conversion. This allows the SLEEP

instruction to be executed, which eliminates all digital

switching noise from the conversion. When the con-

version is completed, the GO/DONE bit will be

cleared, and the result loaded into the ADRES regis-

ter. If the A/D interrupt is enabled, the device will

wake-up from SLEEP. If the A/D interrupt is not

enabled, the A/D module will then be turned off,

although the ADON bit will remain set.

When the A/D clock source is another clock option (not

RC), a SLEEP instruction will cause the present conver-

sion to be aborted and the A/D module to be turned off,

though the ADON bit will remain set.

Turning off the A/D places the A/D module in its lowest

current consumption state.

12.6

Effects of a RESET

A device reset forces all registers to their reset state.

The A/D module is disabled and any conversion in

progress is aborted. All pins with analog functions are

configured as available inputs.

The ADRES register will contain unknown data after a

power-on reset.

12.7

Use of the CCP Trigger

An A/D conversion can be started by the “special event

trigger” of the CCP2 module. This requires that the

CCP2M<3:0> bits (CCP2CON<3:0>) be programmed as

1011

and that the A/D module is enabled (ADON bit is

set). When the trigger occurs, the GO/DONE bit will be

set, starting the A/D conversion, and the Timer1 counter

will be reset to zero. Timer1 is reset to automatically

repeat the A/D acquisition period with minimal software

overhead (moving the ADRES to the desired location).

The appropriate analog input channel must be selected

and the minimum acquisition done before the “special

event trigger” sets the GO/DONE bit (starts a conversion).

If the A/D module is not enabled (ADON is cleared),

then the “special event trigger” will be ignored by the

A/D module, but will still reset the Timer1 counter.

TABLE 12-2:

SUMMARY OF A/D REGISTERS

Note:

For the A/D module to operate in SLEEP,

the A/D clock source must be set to RC

(ADCS<1:0> = 11). To perform an A/D

conversion in SLEEP, ensure the SLEEP

instruction immediately follows the instruc-

tion that sets the GO/DONE bit.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on:

POR,

BOR

Value on all

other

Resets

0Bh,8Bh,

10Bh,18Bh

INTCON

GIE

PEIE

T0IE

INTE

RBIE

T0IF

INTF

RBIF

0000 000x

0000 000u

0Ch

PIR1

PSPIF(1)

ADIF

RCIF

TXIF

USBIF

CCP1IF

TMR2IF TMR1IF 0000 0000 0000 0000

8Ch

PIE1

PSPIE(1)

ADIE

RCIE

TXIE

USBIE

CCP1IE

TMR2IE TMR1IE 0000 0000 0000 0000

1Eh

ADRES

A/D Result Register

xxxx xxxx

uuuu uuuu

1Fh

ADCON0

ADCS1

ADCS0

CHS2

CHS1

CHS0

GO/

DONE

—ADON

0000 00-0

9Fh

ADCON1

—

PCFG2

PCFG1

PCFG0

---- -000

05h

PORTA

—

RA5

RA4

RA3

RA2

RA1

RA0

--0x 0000

--0u 0000

85h

TRISA

—

PORTA Data Direction Register

--11 1111

09h

PORTE

—

RE2(1)

RE1(1)

RE0(1)

---- -xxx

---- -uuu

89h

TRISE

IBF(1)

OBF(1)

IBOV(1)

PSP-MODE(1)

—

PORTE(1) Data Direction Bits

0000 -111

Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used for A/D conversion.

Note 1:

These bits are reserved on the PIC6C745; always maintain these bits clear.

PIC16C765/P Datasheet(PDF) 94 Page - Microchip Technology

PIC16C765/P Datasheet(HTML) 94 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL