PIC16C765SLASHP datasheet(87/158 Pages) MICROCHIP

87 / 158 page

Advanced Information

DS41124A-page 87

PIC16C745/765

11.4

USART Synchronous Slave Mode

Synchronous slave mode differs from the Master mode

in the fact that the shift clock is supplied externally at

the RC6/TX/CK pin (instead of being supplied internally

in master mode). This allows the device to transfer or

receive data while in SLEEP mode. Slave mode is

entered by clearing bit CSRC (TXSTA<7>).

11.4.1

USART SYNCHRONOUS SLAVE

TRANSMIT

The operation of the synchronous master and slave

modes are identical, except in the case of the SLEEP

mode.

If two words are written to the TXREG and then the

SLEEP

instruction is executed, the following will occur:

The first word will immediately transfer to the

TSR register and transmit.

The second word will remain in TXREG register.

Flag bit TXIF will not be set.

When the first word has been shifted out of TSR,

the TXREG register will transfer the second

word to the TSR and flag bit TXIF will now be

set.

If enable bit TXIE is set, the interrupt will wake

the chip from SLEEP and if the global interrupt

is enabled, the program will branch to the inter-

rupt vector (0004h).

Steps to follow when setting up a synchronous slave

transmission:

Enable the synchronous slave serial port by set-

ting bits SYNC and SPEN and clearing bit

CSRC.

Clear bits CREN and SREN.

If interrupts are desired, then set enable bit

TXIE.

If 9-bit transmission is desired, set bit TX9.

Enable the transmission by setting enable bit

TXEN.

If 9-bit transmission is selected, the ninth bit

should be loaded in bit TX9D.

Start transmission by loading data to the

TXREG register.

11.4.2

USART SYNCHRONOUS SLAVE

RECEPTION

The operation of the synchronous master and slave

modes is identical, except in the case of the SLEEP

mode. Also, bit SREN is a don’t care in slave mode.

If receive is enabled by setting bit CREN prior to the

SLEEP

instruction, a word may be received during

SLEEP. On completely receiving the word, the RSR

and if enable bit RCIE bit is set, the interrupt generated

will wake the chip from SLEEP. If the global interrupt is

enabled, the program will branch to the interrupt vector

(0004h).

Steps to follow when setting up a Synchronous Slave

Reception:

Enable the synchronous master serial port by

setting bits SYNC and SPEN and clearing bit

CSRC.

If interrupts are desired, set enable bit RCIE.

If 9-bit reception is desired, set bit RX9.

To enable reception, set enable bit CREN.

Flag bit RCIF will be set when reception is com-

plete and an interrupt will be generated, if

enable bit RCIE was set.

Read the RCSTA register to get the ninth bit (if

enabled) and determine if any error occurred

during reception.

Read the 8-bit received data by reading the

RCREG register.

If any error occurred, clear the error by clearing

bit CREN.

PIC16C765/P Datasheet(PDF) 87 Page - Microchip Technology

PIC16C765/P Datasheet(HTML) 87 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL