CS5530A datasheet(69/259 Pages) AMD

69 / 259 page

AMD Geode™ CS5530A Companion Device Data Book

Power Management

Revision 1.1

F0 Index 9Eh-9Fh

Keyboard / Mouse Idle Timer Count Register (R/W)

Reset Value = 0000h

15:0

Keyboard / Mouse Idle Timer Count: The idle timer loaded from this register determines when the keyboard and mouse

are not in use so that the LCD screen can be blanked. The 16-bit value programmed here represents the period of inactivity

for these ports after which the system is alerted via an SMI. The timer is automatically reloaded with the count value when-

ever an access occurs to either the keyboard or mouse I/O address spaces, including the mouse serial port address space

when a mouse is enabled on a serial port. The timer uses a 1 second timebase.

To enable this timer set F0 Index 81h[3] = 1.

Top level SMI status is reported at F1BAR+Memory Offset 00h/02h[0].

Second level SMI status is reported at F0 Index 85h/F5h[3].

Table 4-18. Keyboard/Mouse Idle Timer and Trap Related Registers (Continued)

Bit

Description

Table 4-19. Parallel/Serial Idle Timer and Trap Related Registers

Bit

Description

F0 Index 81h

Power Management Enable Register 2 (R/W)

Reset Value = 00h

Parallel/Serial Idle Timer Enable: Load timer from Parallel/Serial Port Idle Timer Count Register (F0 Index 9Ch) and gen-

erate an SMI when the timer expires. 0 = Disable; 1 = Enable.

If an access occurs in the address ranges (listed below) the timer is reloaded with the programmed count.

LPT1: I/O Port 378h-37Fh, 778h-77Ah

LPT2: I/O Port 278h-27Fh, 678h-67Ah

COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is excluded)

COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is excluded)

COM3: I/O Port 3E8h-3EFh

COM4: I/O Port 2E8h-2EFh

Top level SMI status is reported at F1BAR+Memory Offset 00h/02h[0].

Second level SMI status is reported at F0 Index 85h/F5h[2].

F0 Index 82h

Power Management Enable Register 3 (R/W)

Reset Value = 00h

Parallel/Serial Trap: 0 = Disable; 1 = Enable.

If this bit is enabled and an access occurs in the address ranges (listed below) an SMI is generated.

LPT1: I/O Port 378h-37Fh, 778h-77Ah

LPT2: I/O Port 278h-27Fh, 678h-67Ah

COM1: I/O Port 3F8h-3FFh (if F0 Index 93h[1:0] = 10 this range is excluded)

COM2: I/O Port 2F8h-2FFh (if F0 Index 93h[1:0] = 11 this range is excluded)

COM3: I/O Port 3E8h-3EFh

COM4: I/O Port 2E8h-2EFh

Top level SMI status is reported at F1BAR+Memory Offset 00h/02h[0].

Second level SMI status is reported at F0 Index 86h/F6h[2].

F0 Index 93h

Miscellaneous Device Control Register (R/W)

Reset Value = 00h

Mouse on Serial Enable: Mouse is present on a serial port. 0 = No; 1 = Yes. (Note)

Mouse Port Select: Selects which serial port the mouse is attached to. 0 = COM1; 1 = COM2. (Note)

Note: Bits 1 and 0 - If a mouse is attached to a serial port (bit 1 = 1), that port is removed from the serial device list being used to

monitor serial port access for power management purposes and added to the keyboard/mouse decode. This is done because a

mouse, along with the keyboard, is considered an input device and is used only to determine when to blank the screen.

These bits determine the decode used for the Keyboard/Mouse Idle Timer Count Register (F0 Index 9Eh) as well as the Parallel/

Serial Port Idle Timer Count Register (F0 Index 9Ch).

F0 Index 9Ch-9Dh

Parallel / Serial Idle Timer Count Register (R/W)

Reset Value = 0000h

15:0

Parallel / Serial Idle Timer Count: The idle timer loaded from this register is used to determine when the parallel and serial

ports are not in use so that the ports can be power managed. The 16-bit value programmed here represents the period of

inactivity for these ports after which the system is alerted via an SMI. The timer is automatically reloaded with the count

value whenever an access occurs to the parallel (LPT) or serial (COM) I/O address spaces. If the mouse is enabled on a

serial port, that port is not considered here. The timer uses a 1 second timebase.

To enable this timer set F0 Index 81h[2] = 1.

Top level SMI status is reported at F1BAR+Memory Offset 00h/02h[0].

Second level SMI status is reported at F0 Index 85h/F5h[2].

CS5530A Datasheet(PDF) 69 Page - Advanced Micro Devices

CS5530A Datasheet(HTML) 69 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL