GRM552B11H102KA01D datasheet(54/221 Pages) MURATA

54 / 221 page

Continued from the preceding page.

Continued on the following page.

Temperature (

°C)

Step

Reference Temperature

±2

–55

±3 (for ∆C to 7U/R6/R7/C8)

–30

±3 (for F5), 10±3 (for E4)

–25

±3 (for other TC)

Reference Temperature

±2

125

±3 (for ∆C/R7), 105±3 (for C8)

±3 (for other TC)

Reference Temperature

±2

Temperature (

°C)

Step

Reference Temperature

±2

–55

±3 (for C8, R1, R7, R6)

–25

±3 (for B1, B3, F1)

–30

±3 (for F5)/10±3 (for E4)

Reference Temperature

±2

125

±3 (for R1, R7)/

±3 (for B1, B3, R6

F1, F5, E4)/105

±3 (for C8)

Reference Temperature

±2

–55

±3 (for R1)/

–25

±3 (for B1, F1)

Reference Temperature

±2

125

±3 (for R1)/

±3 (for B1, F1)

Applying Voltage (V)

No bias

50% of the rated

voltage

Type

0.2

0.3

0.4

1.0

1.2

2.2

3.5

4.5

0.56

0.9

1.5

3.0

4.0

5.0

7.0

8.0

0.23

0.3

0.5

1.2

1.65

2.0

2.9

3.7

5.6

GRM02

GRM03

GRM15

GRM18

GRM21

GRM31

GRM32

GRM43

GRM55

Solder the capacitor to the test jig (glass epoxy board) shown in

Fig. 1a using a eutectic solder. Then apply 10N* force in

parallel with the test jig for 10

±1 sec.

The soldering should be done either with an iron or using the

reflow method and should be conducted with care so that the

soldering is uniform and free of defects such as heat shock.

*1N (GRM02), 2N (GRM03), 5N (GRM15, GRM18)

(in mm)

Adhesive Strength

of Termination

No removal of the terminations or other defect should occur.

Fig. 1a

The capacitance change should be measured after 5 min. at

each specified temp. stage.

(1)Temperature Compensating Type

The temperature coefficient is determined using the

capacitance measured in step 3 as a reference.

When cycling the temperature sequentially from steps 1

through 5 (5C: +25 to +125

°C/∆C: +20 to +125°C: other temp.

coeffs.: +25 to +85

°C/+20 to +85°C) the capacitance should be

within the specified tolerance for the temperature coefficient

and capacitance change as in Table A-1.

The capacitance drift is calculated by dividing the differences

between the maximum and minimum measured values in the

steps 1, 3 and 5 by the cap. value in step 3.

(2) High Dielectric Constant Type

The ranges of capacitance change compared with the

Reference Temperature value over the temperature ranges

shown in the table should be within the specified ranges.*

When applying voltage, the capacitance change should be

measured after 1 more min. with applying voltage in

equilibration of each temp. stage.

Capacitance

Temperature

Characteristics

No bias

Within the specified tolerance

(Table A-1)

B1, B3: Within

±10%

(–25 to +85

°C)

R1, R7: Within

±15%

(–55 to +125

°C)

R6: Within

±15%

(–55 to +85

°C)

E4: Within +22/–56%

(+10 to +85

°C)

F1: Within +30/–80%

(–25 to +85

°C)

F5: Within +22/–82%

(–30 to +85

°C)

C8: Within

±22%

(–55 to +105

°C)

50% of

the Rated

Voltage

B1: Within +10/–30%

R1: Within +15/–40%

F1: Within +30/–95%

Capacitance

Drift

Within

±0.2% or ±0.05pF

(whichever is larger.)

*Do not apply to 1X/25V

*Initial measurement for high

dielectric constant type

Perform a heat treatment at

150+0/–10

°C for one hour

and then set for 24

±2 hours

at room temperature.

Perform the initial

measurement.

No.

Test Method

Specifications

Temperature

Compensating Type

High Dielectric Type

Item

Baked electrode or

copper foil

Solder resist

GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

(Note 1) These Specifications and Test Methods indicate typical inspection.

Please refer to individual specifications (our product specifications or the approval sheet).

When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).

When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 54 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 54 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL