GRM552B11H102KA01D datasheet(60/221 Pages) MURATA

60 / 221 page

Continued from the preceding page.

Continued on the following page.

Solder the capacitor on the test jig (glass epoxy board) in the

same manner and under the same conditions as (10).

The capacitor should be subjected to a simple harmonic motion

having a total amplitude of 1.5mm, the frequency being varied

uniformly between the approximate limits of 10 and 55Hz. The

frequency range, from 10 to 55Hz and return to 10Hz, should

be traversed in approximately 1 minute. This motion should be

applied for a period of 2 hours in each of 3 mutually

perpendicular directions (total of 6 hours).

Vibration

Appearance

No defects or abnormalities

Capacitance

Within the specified tolerance

D.F.

B1, B3, R1, *R6, *R7, C7, C8, E7, D7: 0.1 max.

C6: 0.125 max.

D8: 0.15 max.

F1, F5: 0.2 max.

*GRM31CR71E106: 0.125 max.

GRM31CR6 0J/0G 107: 0.15 max.

Solder the capacitor on the test jig (glass epoxy board) shown

in Fig. 1a using a eutectic solder. Then apply 10N* force in

parallel with the test jig for 10

±1sec.

The soldering should be done either with an iron or using the

reflow method and should be conducted with care so that the

soldering is uniform and free of defects such as heat shock.

*1N: GRM02, 2N: GRM03, 5N: GRM15/GRM18

Adhesive Strength

of Termination

No removal of the terminations or other defects should occur.

Fig. 1a

GRM Series Specifications and Test Methods (2) (Note 1)-Typical Inspection

Type

0.2

0.3

0.4

1.0

1.2

2.2

3.5

4.5

0.56

0.9

1.5

3.0

4.0

5.0

7.0

8.0

0.23

0.3

0.5

1.2

1.65

2.0

2.9

3.7

5.6

GRM02

GRM03

GRM15

GRM18

GRM21

GRM31

GRM32

GRM43

GRM55

Baked electrode or

copper foil

Solder resist

The capacitance change should be measured after 5 min. at

each specified temp. stage.

The ranges of capacitance change compared with the

reference temperature value over the temperature ranges

shown in the table should be within the specified ranges.*

In case of applying voltage, the capacitance change should be

measured after 1 more min. with applying voltage in

equilibration of each temp. stage.

*GRM32DR60J226, GRM43 B1/B3/R6 0J/1A 336/476: 1.0

±0.2Vrms

GRM155B30G475, GRM155B30J 225, GRM21BB30J476,

GRM155R60E106, GRM188 B3/R6 0E/0G/0J 226: 0.2

±0.05Vrms

•Initial measurement for high dielectric constant type

Perform a heat treatment at 150 +0/–10

°C for one hour and

then set for 24

±2 hours at room temperature.

Perform the initial measurement.

Capacitance

Temperature

Characteristics

No bias

B1, B3 : Within

±10% (–25 to +85°C)

: Within +30/–80% (–25 to +85

°C)

: Within

±15% (–55 to +85°C)

R1, R7 : Within

±15% (–55 to +125°C)

: Within +22/–82% (–30 to +85

°C)

: Within

±22% (–55 to +85°C)

: Within

±22% (–55 to +125°C)

: Within

±22% (–55 to +105°C)

: Within +22/–33% (–55 to +125

°C)

: Within +22/–56% (–55 to +125

°C)

: Within +22/–33% (–55 to +105

°C)

50% of

the Rated

Voltage

B1: Within +10/–30%

R1: Within +15/–40%

F1: Within +30/–95%

Temperature (

°C)

Step

±2 (for R6, R7, C6, C7, C8, D7, D8, E7, F5)

±2 (for B1, B3, F1, R1)

–55

±3 (for R1, R6, R7, C6, C7, C8, D7, D8, E7)

–30

±3 (for F5)

–25

±3 (for B1, B3, F1)

±2 (for R6, R7, C6, C7, C8, D7, D8, E7, F5)

±2 (for B1, B3, F1, R1)

125

±3 (for R1, R7, C7, D7, E7)

105

±3 (for C8, D8)

±3 (for B1, B3, F1, F5, R6, C6)

±2 (for B1, F1, R1)

–55

±3 (for R1)

–25

±3 (for B1, F1)

±2 (for B1, F1, R1)

125

±3 (for R1)

±3 (for B1, F1)

Applying Voltage (V)

No bias

50% of the

rated voltage

No.

Test Method

Specifications

Item

GRM Series Specifications and Test Methods (2) (Note 1)-Typical Inspection

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

(Note 1) These Specifications and Test Methods indicate typical inspection.

Please refer to individual specifications (our product specifications or the approval sheet).

When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).

When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 60 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 60 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL