GRM552B11H102KA01D datasheet(72/221 Pages) MURATA

72 / 221 page

Continued on the following page.

GNM Series Specifications and Test Methods (1)

Solder the capacitor to the test jig (glass epoxy board) shown in

Fig.1 using a eutectic solder. Then apply 5N force in parallel with

the test jig for 10

±1 sec.

The soldering should be done either with an iron or using the

reflow method and should be conducted with care so that the

soldering is uniform and free of defects such as heat shock.

(in mm)

Fig. 1

Adhesive Strength

of Termination

No removal of the terminations or other defect should occur.

GNMpp4

GNMpp2

The capacitance change should be measured after 5 min. at

each specified temperature stage.

(1) Temperature Compensating Type

The temperature coefficient is determined using the capaci-

tance measured in step 3 as a reference. When cycling the

temperature sequentially from steps 1 through 5, the

capacitance should be within the specified tolerance for the

temperature coefficient and capacitance change as in Table A.

The capacitance drift is calculated by dividing the differences

between the maximum and minimum measured values in the

steps 1, 3 and 5 by the cap. value in step 3.

(2) High Dielectric Constant Type

The ranges of capacitance change compared with the above

°C value over the temperature ranges shown in the table

should be within the specified ranges.

Capacitance

Temperature

Characteristics

Capacitance

Change

Within the

specified tolerance

(Table A)

Temperature

Coefficient

Within the

specified tolerance

(Table A)

Capacitance

Drift

Within

±0.2%

±0.05pF

(whichever is

larger.)

Dissipation Factor

(D.F.)

30pF min.: Q

U1000

30pF max.:

U400+20C

C: Nominal

Capacitance (pF)

The capacitance/Q/D.F. should be measured at 25

°C at the

frequency and voltage shown in the table.

Capacitance

Within the specified tolerance

The insulation resistance should be measured with a DC

voltage not exceeding the rated voltage at 25

°C and 75%RH

max. and within 2 minutes of charging.

Insulation

Resistance

More than 10,000M

Ω or 500Ω · F

(whichever is smaller)

No failure should be observed when 300% of the rated voltage

(5C) or 250% of the rated voltage (R7) is applied between the

terminations for 1 to 5 seconds, provided the charge/discharge

current is less than 50mA.

Dielectric Strength

No defects or abnormalities

Using calipers

Dimensions

Within the specified dimensions

Visual inspection

Appearance

No defects or abnormalities

The rated voltage is defined as the maximum voltage that may

be applied continuously to the capacitor.

When AC voltage is superimposed on DC voltage, VP-P or VO-P,

whichever is larger, should be maintained within the rated

voltage range.

Rated Voltage

See the previous pages.

Operating

Temperature

Range

5C: –55 to +125

°C

R7, C7: –55 to +125

°C

R6: –55 to +85

°C

No.

Test Method

Specifications

Temperature

Compensating Type

High Dielectric Type

Item

Step

Temperature (

°C)

±2

–55

±3 (for 5C/R7/C7), –30±3 (for F5)

±2

125

±3 (for 5C/R7/C7), 85±3 (for F5)

±2

Char.

Item

±0.1MHz

0.5 to 5Vrms

±0.1kHz

1.0

±0.2Vrms

Frequency

Voltage

Char. 25V min.

0.025

max.

16V

0.035

max.

10V

0.035

max.

6.3V

0.05

max.

R7, R6,

Char.

Temp.

Range

–55

°C

to +125

°C

Reference

Temp.

°C

Cap.

Change

Within

±15%

–55

°C

to +85

°C

Within

±22%

–55

°C

to +125

°C

Type

0.5

0.6

0.8

1.6

1.8

2.0

2.5

0.32

0.5

0.25

0.4

0.32

0.5

0.25

0.4

GNM1M2

GNM212

GNM214

GNM314

Solder resist

Copper foil

Solder resist

Copper foil

• Initial measurement for high dielectric constant type.

Perform a heat treatment at 150+0/-10

°C for one hour and

then set for 24

±2 hours at room temperature.

Perform the initial measurement.

!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.

0. Please check with our sales representatives or product engineers before ordering.

2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product

0. specifications before ordering.

GNM Series Specifications and Test Methods (1)

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).

When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 72 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 72 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL