 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
GRM552B11H102KA01D Datasheet(PDF) 74 Page - Murata Manufacturing Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
GRM552B11H102KA01D Datasheet(HTML) 74 Page - Murata Manufacturing Co., Ltd. |
|
|
74 / 221 page  Continued from the preceding page. Continued on the following page. Apply the rated voltage at 40 ±2°C and 90 to 95% humidity for 500 ±12 hours. Remove and let sit for 24 ±2 hours at room temperature, then measure. The charge/discharge current is less than 50mA. 17 Humidity Load The measured and observed characteristics should satisfy the specifications in the following table. Appearance No marking defects Capacitance Change Within ±7.5% or ±0.75pF (whichever is larger) R7, R6, C7: Within ±12.5% Q/D.F. 30pF and over: Q U200 30pF and below: Q U100+10C/3 C: Nominal Capacitance (pF) I.R. More than 500M Ω or 25Ω · F (whichever is smaller) Set the capacitor at 40 ±2°C and 90 to 95% humidity for 500±12 hours. Remove and let sit for 24 ±2 hours at room temperature, then measure. 16 Humidity Steady State The measured and observed characteristics should satisfy the specifications in the following table. Appearance No marking defects Capacitance Change Within ±5% or ±0.5pF (whichever is larger) R7, R6, C7: Within ±12.5% Q/D.F. 30pF and over: Q U350 10pF and over, 30pF and below: Q U275+5C/2 10pF and below: Q U200+10C C: Nominal Capacitance (pF) I.R. More than 1,000M Ω or 50Ω · F (whichever is smaller) Fix the capacitor to the supporting jig in the same manner and under the same conditions as (10). Perform the five cycles according to the four heat treatments listed in the following table. Let sit for 24 ±2 hours (temperature compensating type) or 48 ±4 hours (high dielectric constant type) at room temperature, then measure. • Initial measurement for high dielectric constant type Perform a heat treatment at 150+0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature. Perform the initial measurement. 15 Temperature Cycle The measured and observed characteristics should satisfy the specifications in the following table. Appearance No marking defects Capacitance Change Within ±2.5% or ±0.25pF (whichever is larger) R7, R6, C7: Within ±7.5% Q/D.F. 30pF min.: Q U1000 30pF max.: Q U400+20C C:Nominal Capacitance (pF) I.R. More than 10,000M Ω or 500Ω · F (whichever is smaller) Dielectric Strength No failure GNM Series Specifications and Test Methods (1) Step Temp. ( °C) Time (min.) 1 Min. Operating Temp.+0/–3 30 ±3 2 Room Temp. 2 to 3 3 Max. Operating Temp. +3/–0 30 ±3 4 Room Temp. 2 to 3 Char. 25V min. 0.025 max. 16V 0.035 max. 10V 0.035 max. 6.3V 0.05 max. R7, R6, C7 Char. 25V min. 0.05 max. 16V 0.05 max. 10V/6.3V 0.05 max. R7, R6, C7 Char. 25V min. 0.05 max. 16V 0.05 max. 10V/6.3V 0.05 max. R7, R6, C7 No. Test Method Specifications Temperature Compensating Type High Dielectric Type Item !Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice. 0. Please check with our sales representatives or product engineers before ordering. 2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product 0. specifications before ordering. GNM Series Specifications and Test Methods (1) 72 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1). When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2). • This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. !Note C02E.pdf 10.12.20 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
