 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
GRM552B11H102KA01D Datasheet(PDF) 73 Page - Murata Manufacturing Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
GRM552B11H102KA01D Datasheet(HTML) 73 Page - Murata Manufacturing Co., Ltd. |
|
|
73 / 221 page  Continued from the preceding page. Continued on the following page. Preheat the capacitor at 120 to 150 °C for 1 minute. Immerse the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder solution at 270 ±5°C for 10±0.5 seconds. Let sit at room temperature for 24 ±2 hours, then measure. • Initial measurement for high dielectric constant type Perform a heat treatment at 150+0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature. Perform the initial measurement. 14 Resistance to Soldering Heat The measured and observed characteristics should satisfy the specifications in the following table. Appearance No marking defects Capacitance Change Within ±2.5% or ±0.25pF (whichever is larger) R7, R6, C7: Within ±7.5% Q/D.F. 30pF min.: Q U1000 30pF max.: Q U400+20C C: Nominal Capacitance (pF) I.R. More than 10,000M Ω or 500Ω · F (whichever is smaller) Dielectric Strength No failure Immerse the capacitor in a solution of ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at 80 to 120 °C for 10 to 30 seconds. After preheating, immerse in eutectic solder solution for 2 ±0.5 seconds at 230±5°C or Sn-3.0Ag-0.5Cu solder solution for 2 ±0.5 seconds at 245±5°C. 13 Solderability of Termination 75% of the terminations are to be soldered evenly and continuously. GNM Series Specifications and Test Methods (1) Char. 25V min. 0.025 max. 16V 0.035 max. 10V 0.035 max. 6.3V 0.05 max. R7, R6, C7 Char. 25V min. 0.025 max. 16V 0.035 max. 10V 0.035 max. 6.3V 0.05 max. R7, R6, C7 Type a 2.0 ±0.05 2.0 ±0.05 2.0 ±0.05 2.5 ±0.05 b 0.5 ±0.05 0.6 ±0.05 0.7 ±0.05 0.8 ±0.05 c 0.32 ±0.05 0.5 ±0.05 0.3 ±0.05 0.4 ±0.05 d 0.32 ±0.05 0.5 ±0.05 0.2 ±0.05 0.4 ±0.05 GNM1M2 GNM212 GNM214 GNM314 Solder the capacitor on the test jig (glass epoxy board) shown in Fig. 2 using a eutectic solder. Then apply a force in the direction shown in Fig. 3 for 5 ±1 sec. The soldering should be done by the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. Fig. 3 12 Deflection Appearance No marking defects Capacitance Change Within ±5% or ±0.5pF (whichever is larger) Within ±10% (in mm) Fig. 2 •GNMpp4 •GNMpp2 Solder the capacitor to the test jig (glass epoxy board) in the same manner and under the same conditions as (10). The capacitor should be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 55Hz. The frequency range, from 10 to 55Hz and return to 10Hz, should be traversed in approximately 1 minute. This motion should be applied for a period of 2 hours in each of 3 mutually perpendic- ular directions (total of 6 hours). 11 Vibration Resistance Appearance No defects or abnormalities Capacitance Within the specified tolerance Q/D.F. 30pF min.: Q U1000 30pF max.: Q U400+20C C: Nominal Capacitance (pF) No. Test Method Specifications Temperature Compensating Type High Dielectric Type Item 100 1.0 5.0 b a c d 100 1.0 t=0.8mm 5.0 b a c d Capacitance meter Flexure : V1 20 50 R230 Pressurizing speed: 1.0mm/sec. Pressurize 45 45 !Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice. 0. Please check with our sales representatives or product engineers before ordering. 2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product 0. specifications before ordering. GNM Series Specifications and Test Methods (1) 71 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1). When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2). • This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. !Note C02E.pdf 10.12.20 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
