 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
GRM552B11H102KA01D Datasheet(PDF) 77 Page - Murata Manufacturing Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
GRM552B11H102KA01D Datasheet(HTML) 77 Page - Murata Manufacturing Co., Ltd. |
|
|
77 / 221 page  Continued from the preceding page. GNM Series Specifications and Test Methods (2) 100 1.0 5.0 b a c d 100 1.0 5.0 b a c d Capacitance meter Flexure : V1 20 50 R230 Pressurizing speed: 1.0mm/sec. Pressurize 45 45 Apply 150% (GNM1M2R61A225/1C105: 125% of the rated voltage) of the rated voltage for 1000 ±12 hours at the maximum operating temperature ±3°C. Let sit for 24±2 hours at room temperature, then measure. The charge/discharge current is less than 50mA. • Initial measurement Perform a heat treatment at 150 +0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature. Perform the initial measurement. • Measurement after test Perform a heat treatment at 150 +0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature, then measure. 17 Durability Appearance No marking defects Capacitance Change R6: Within ±12.5% D.F. 0.2 max. I.R. 25 Ω · F min. Apply the rated voltage at 40 ±2°C and 90 to 95% humidity for 500 ±12 hours. The charge/discharge current is less than 50mA. • Initial measurement Perform a heat treatment at 150 +0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature. Perform the initial measurement. • Measurement after test Perform a heat treatment at 150 +0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature, then measure. 16 High Temperature High Humidity (Steady) Appearance No marking defects Capacitance Change R6: Within ±12.5% D.F. 0.2 max. I.R. 12.5 Ω · F min. Fix the capacitor to the supporting jig in the same manner and under the same conditions as (10). Perform the five cycles according to the four heat treatments listed in the following table. Let sit for 24 ±2 hours at room temperature, then measure. • Initial measurement Perform a heat treatment at 150 +0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature. Perform the initial measurement. 15 Temperature Cycle Appearance No marking defects Capacitance Change R6*5: Within ±12.5% *5 GNM0M2R60G105, GNM0M2R60J103/223/473/104, GNM0M2R61A103/223/473/104, GNM0M2R61C103/223/473/104, GNM1M2R61A105: Within ±15% D.F. 0.1 max. *3 *3 However 0.125 max. for Table 3 items. I.R. 50 Ω · F min. Dielectric Strength No failure Preheat the capacitor at 120 to 150 °C for 1 minute. Immerse the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder solution at 270 ±5°C for 10±0.5 seconds. Let sit at room temperature for 24 ±2 hours, then measure. • Initial measurement Perform a heat treatment at 150 +0/-10 °C for one hour and then let sit for 24 ±2 hours at room temperature. Perform the initial measurement. 14 Resistance to Soldering Heat Appearance No marking defects Capacitance Change R6*4: Within ±7.5% *4 GNM0M2R60G105: Within +15/-7.5% D.F. 0.1 max. *3 *3 However 0.125 max. for Table 3 items. I.R. 50 Ω · F min. Dielectric Strength No failure Immerse the capacitor in a solution of ethanol (JIS-K-8101) and rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at 80 to 120 °C for 10 to 30 seconds. After preheating, immerse in eutectic solder solution for 2 ±0.5 seconds at 230±5°C or Sn-3.0Ag-0.5Cu solder solution for 2 ±0.5 seconds at 245±5°C. 13 Solderability of Termination 75% of the terminations are to be soldered evenly and continuously. Solder the capacitor to the test jig (glass epoxy board) shown in Fig. 2 using a eutectic solder. Then apply a force in the direction shown in Fig. 3. The soldering should be done by the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. 12 Deflection Appearance No marking defects Capacitance Change Within ±10% No. Test Method Specifications Item Fig. 3 Fig. 2 Thickness: 0.8mm #GNMpp4 #GNMpp2 1 Step Min. Operating Temp. 30 ±3 2 Room Temp. 2 to 3 3 Min. Operating Temp. 30 ±3 4 Room Temp. 2 to 3 Temp. ( °C) Time (min.) a Type 2.0 ±0.05 2.0 ±0.05 2.0 ±0.05 2.0 ±0.05 2.5 ±0.05 b 0.2 ±0.05 0.5 ±0.05 0.6 ±0.05 0.7 ±0.05 0.8 ±0.05 c 0.2 ±0.05 0.32 ±0.05 0.5 ±0.05 0.3 ±0.05 0.4 ±0.05 d 0.25 ±0.05 0.32 ±0.05 0.5 ±0.05 0.2 ±0.05 0.4 ±0.05 GNM0M2 GNM1M2 GNM212 GNM214 GNM314 (in mm) !Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice. 0. Please check with our sales representatives or product engineers before ordering. 2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product 0. specifications before ordering. GNM Series Specifications and Test Methods (2) 75 !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. • This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1). When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2). • This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. • This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. !Note C02E.pdf 10.12.20 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
