GRM552B11H102KA01D datasheet(99/221 Pages) MURATA

99 / 221 page

GJM Series Specifications and Test Methods (1)

!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.

0. Please check with our sales representatives or product engineers before ordering.

2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product

0. specifications before ordering.

See the previous pages.

Within the specified dimensions

No defects or abnormalities

10,000M

Ω min. or 500Ω · F min. (whichever is smaller)

No defects or abnormalities

Y55 to W125D

Operating

Temperature Range

Rated Voltage

Appearance

Dimensions

Dielectric Strength

Insulation Resistance

(I.R.)

Using calipers

The insulation resistance should be measured with a DC

voltage not exceeding the rated voltage at 25

D and 75%RH

max. and within 2 minutes of charging.

No failure should be observed when 300% of the rated voltage

is applied between the terminations for 1 to 5 seconds,

provided the charge/discharge current is less than 50mA.

Visual inspection

The rated voltage is defined as the maximum voltage that may

be applied continuously to the capacitor.

When AC voltage is superimposed on DC voltage, VP-P or VO-P,

whichever is larger, should be maintained within the rated

voltage range.

Reference Temperature: 25

(2C, 3C, 4C: 20

30pF and over: Q

U1000

30pF and below: Q

U400W20C

C: Nominal Capacitance (pF)

Within the specified tolerance

Capacitance

The capacitance/Q should be measured at 25

D at the

frequency and voltage shown in the table.

Continued on the following page.

No removal of the terminations or other defect should occur.

Adhesive Strength

of Termination

Solder the capacitor to the test jig (glass epoxy board) shown in

Fig. 1 using a eutectic solder. Then apply a 5N* force in parallel

with the test jig for 10

T1 sec. The soldering should be done either

with an iron or using the reflow method and should be conducted

with care so that the soldering is uniform and free of defects such

as heat shock.

*2N (GJM03)

Baked electrode or

copper foil

Solder resist

Frequency

T0.1MHz

Voltage

0.5 to 5Vrms

Within the specified tolerance (Table A)

Within

T0.2% or T0.05pF

(whichever is larger.)

Temperature

Coefficient

Capacitance

Drift

Capacitance

Temperature

Characteristics

The capacitance change should be measured after 5 min. at

each specified temperature stage.

Temperature Compensating Type

The temperature coefficient is determined using the

capacitance measured in step 3 as a reference.

When cycling the temperature sequentially from step 1 through

5, (5C:

W25 to 125D: other temp. coeffs.: W20 to 125D) the

capacitance should be within the specified tolerance for the

temperature coefficient and capacitance change as in Table A.

The capacitance drift is calculated by dividing the differences

between the maximum and minimum measured values in steps

1, 3 and 5 by the capacitance value in step 3.

Step

Reference Temp.

Y55T3

Reference Temp.

125

Reference Temp.

Temperature (

(in mm)

Fig. 1

Type

GJM03

GJM15

0.3

0.4

0.9

1.5

0.3

0.5

No.

Item

Specifications

Test Method

Temperature Compensating Type

GJM Series Specifications and Test Methods

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 99 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 99 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL