GRM552B11H102KA01D datasheet(76/221 Pages) MURATA

76 / 221 page

Solder the capacitor to the test jig (glass epoxy board) in

the same manner and under the same conditions as (10).

The capacitor should be subjected to a simple harmonic motion

having a total amplitude of 1.5mm, the frequency being varied

uniformly between the approximate limits of 10 and 55Hz.

The frequency range, from 10 to 55Hz and return to 10Hz,

should be traversed in approximately 1 minute. This motion

should be applied for a period of 2 hours in each of 3 mutually

perpendicular directions (total of 6 hours).

Vibration

Appearance

No defects or abnormalities

Capacitance

Within the specified tolerance

D.F.

0.1 max.*3

*3 However 0.125 max. for Table 3 items.

Continued on the following page.

Temperature (

°C)

Step

±2

–55

±3

±2

±3

±2

Temp. Range

Char.

–55 to +85

°C

Reference

Temp.

°C

Cap. Change

Within

±15%

Type

0.2

0.5

0.6

0.8

0.96

1.6

1.8

2.0

2.5

0.25

0.32

0.5

0.25

0.4

0.2

0.32

0.5

0.25

0.4

GNM0M2

GNM1M2

GNM212

GNM214

GNM314

Solder the capacitor to the test jig (glass epoxy board) shown in

Fig. 1 using a eutectic solder.

Then apply 5N (GNM0M2: 2N) force in parallel with the test jig for

±1 sec. The soldering should be done either with an iron or

using the reflow method and should be conducted with care so that

the soldering is uniform and free of defects such as heat shock.

(in mm)

Adhesive Strength

of Termination

No removal of the terminations or other defects should occur.

The capacitance change should be measured after 5 min.at

each specified temperature stage.

The ranges of capacitance change compared with the 25

°C

value over the temperature ranges shown in the table should be

within the specified ranges.

• Initial measurement for high dielectric constant type.

Perform a heat treatment at 150+0/-10

°C for one hour and

then set for 24

±2 hours at room temperature.

Perform the initial measurement.

Capacitance

Temperature

Characteristics

Dissipation Factor

(D.F.)

0.1 max.*3

Table 3

*3 However 0.125 max. for Table 3 items.

The capacitance/D.F. should be measured at 25

°C at the

frequency and voltage shown in the table.

Table 1

Table 2

Capacitance

Within the specified tolerance

The insulation resistance should be measured with a DC

voltage not exceeding the rated voltage at 25

°C and 75%RH

max. and within 1 minute of charging.

Insulation Resistance

Ω · F min.

No failure should be observed when 250% of the rated voltage

is applied between the terminations for 1 to 5 seconds,

provided the charge/discharge current is less than 50mA.

Dielectric Strength

No defects or abnormalities

Using calipers

Dimensions

Within the specified dimension

Visual inspection

Appearance

No defects or abnormalities

The rated voltage is defined as the maximum voltage that may

be applied continuously to the capacitor.

When AC voltage is superimposed on DC voltage, VP-P or VO-P,

whichever is larger, should be maintained within the rated

voltage range.

Rated Voltage

See the previous pages.

Operating

Temperature Range

R6: –55

°C to +85°C

Measuring Frequency

Nominal Capacitance

±0.1kHz

Measuring Voltage

1.0

±0.2Vrms

0.5

±0.1Vrms

0.5

±0.1Vrms

1.0

±0.1Vrms

V10µF *1 (10V min.)

V10µF *2 (6.3V max.)

*1For items in Table1

*2For items in Table2

GNM Series Specifications and Test Methods (2)

Solder resist

Copper foil

Solder resist

Copper foil

No.

Test Method

Specifications

Item

Fig. 1

GNMpp4

GNMpp2

GNM0M2 R6 1A 104

GNM0M2 R6 1C 104

GNM1M2 R6 1A 105/225

GNM1M2 R6 1C 224/105

GNM0M2 R6 0J

103/223/473

GNM212

R6 0J

225

GNM214

R6 0J

105

GNM0M2 R6 103/223/473/104

GNM1M2 R6 0J

105/225

GNM1M2 R6 1A 105MEA4

GNM1M2 R6 1A 225

GNM212

R6 0J

225

GNM212

R6 1A 225

GNM214

R6 0J

225

!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.

0. Please check with our sales representatives or product engineers before ordering.

2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product

0. specifications before ordering.

GNM Series Specifications and Test Methods (2)

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

When no "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (1).

When "*" is added in PNs table, please refer to GNM Series Specifications and Test Methods (2).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 76 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 76 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL