GRM552B11H102KA01D datasheet(55/221 Pages) MURATA

55 / 221 page

Immerse the capacitor in a solution of ethanol (JIS-K-8101) and

rosin (JIS-K-5902) (25% rosin in weight proportion).

Preheat at 80 to 120

°C for 10 to 30 seconds.

After preheating, immerse in a eutectic solder solution for

±0.5 seconds at 230±5°C or Sn-3.0Ag-0.5Cu solder solution

for 2

±0.5 seconds at 245±5°C.

Solderability of

Termination

75% of the terminations are to be soldered evenly and

continuously.

Continued from the preceding page.

Continued on the following page.

Solder the capacitor on the test jig (glass epoxy board) shown

in Fig. 2a using a eutectic solder. Then apply a force in the

direction shown in Fig. 3a for 5

±1 sec. The soldering should be

done by the reflow method and should be conducted with care

so that the soldering is uniform and free of defects such as heat

shock.

Fig. 2a

(in mm)

Deflection

Appearance

No marking defects

Capacitance

Change

Within

±5% or ±0.5pF

(whichever is larger)

Within

±10%

Fig. 3a

Solder the capacitor on the test jig (glass epoxy board) in the

same manner and under the same conditions as (10).

The capacitor should be subjected to a simple harmonic motion

having a total amplitude of 1.5mm, the frequency being varied

uniformly between the approximate limits of 10 and 55Hz. The

frequency range, from 10 to 55Hz and return to 10Hz, should

be traversed in approximately 1 minute. This motion should be

applied for a period of 2 hours in each of 3 mutually

perpendicular directions (total of 6 hours).

Vibration

Resistance

Appearance

No defects or abnormalities

Capacitance

Within the specified tolerance

Q/D.F.

30pF and over: Q

U1000

30pF and below:

U400+20C

C: Nominal Capacitance (pF)

[B1, B3, R6, R7, C8]

W.V.: 100V

: 0.025 max. (C

F0.068µF)

: 0.05 max. (C

U0.068µF)

W.V.: 50/35/25V:

: 0.025 max.*

*GRM32D R7/R6/C8 1E106: 0.035 max.

W.V.: 16/10V: 0.035 max.

W.V.: 6.3/4V

: 0.05 max. (C

F3.3µF)

: 0.1 max. (C

U3.3µF)

[E4]

W.V.: 25Vmin: 0.025 max.

[F1, F5]

W.V.: 25V min.

: 0.05 max. (C

F0.1µF)

: 0.09 max. (C

U0.1µF)

W.V.: 16/10V: 0.125 max.

W.V.: 6.3V: 0.15 max.

Capacitance meter

Flexure :

R230

Pressurizing

speed: 1.0mm/sec.

Pressurize

100

t: 1.6mm (GRM02/03/15: t: 0.8mm)

φ4.5

Type

0.2

0.3

0.4

1.0

1.2

2.2

3.5

4.5

0.56

0.9

1.5

3.0

4.0

5.0

7.0

8.0

0.23

0.3

0.5

1.2

1.65

2.0

2.9

3.7

5.6

GRM02

GRM03

GRM15

GRM18

GRM21

GRM31

GRM32

GRM43

GRM55

No.

Test Method

Specifications

Temperature

Compensating Type

High Dielectric Type

Item

GRM Series Specifications and Test Methods (1) (Note 1)-Typical Inspection

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

(Note 1) These Specifications and Test Methods indicate typical inspection.

Please refer to individual specifications (our product specifications or the approval sheet).

When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).

When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 55 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 55 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL