GRM552B11H102KA01D datasheet(61/221 Pages) MURATA

61 / 221 page

Continued from the preceding page.

Fix the capacitor to the supporting jig in the same manner and

under the same conditions as (10).

Perform the five cycles according to the four heat treatments

shown in the following table.

Set for 24

±2 hours at room temperature, then measure.

•Initial measurement for high dielectric constant type

Perform a heat treatment at 150+0/–10

°C for one hour and

then set at room temperature for 24

±2 hours.

Perform the initial measurement.

GRM188R60J106 only Measurement after test Perform a heat

treatment and then let sit for 24

±2 hours at room temperature,

then measure.

Temperature

Sudden

Change

Appearance

No defects or abnormalities

Dielectric

Strength

No defects

I.R.

More than 50

Ω · F

D.F.

B1, B3, R1, *R6, *R7, C7, C8, E7, D7: 0.1 max.

C6: 0.125 max.

D8: 0.15 max.

F1, F5: 0.2 max.

*GRM31CR71E106: 0.125 max.

GRM31CR6 0J/0G 107: 0.15 max.

Capacitance

Change

B1, B3, R1, R6, R7, C6, C7, C8, D7, D8: Within

±7.5%

E7: Within

±30%

F1, F5: Within

±20%

Preheat the capacitor at 120 to 150

°C for 1 minute.

Immerse the capacitor in a eutectic solder* or Sn-3.0Ag-0.5Cu

solder solution at 270

±5°C for 10±0.5 seconds. Set at room

temperature for 24

±2 hours, then measure.

*Do not apply to GRM02.

•Initial measurement for high dielectric constant type

Perform a heat treatment at 150+0/–10

°C for one hour and

then set at room temperature for 24

±2 hours.

Perform the initial measurement.

*Preheating for GRM32/43/55

Resistance

Soldering

Heat

Appearance

No defects or abnormalities

Dielectric

Strength

No defects

I.R.

More than 50

Ω · F

D.F.

B1, B3, R1, *R6, *R7, C7, C8, E7, D7: 0.1 max.

C6: 0.125 max.

D8: 0.15 max.

F1, F5: 0.2 max.

*GRM31CR71E106: 0.125 max.

GRM31CR6 0J/0G 107: 0.15 max.

Capacitance

Change

B1, B3, R1, *R6, R7, C6, C7, *C8, E7, D7, D8: Within

±7.5%

F1, F5: Within

±20%

*GRM188R6 0J/0G 106, GRM188C8 0E/0G 106, GRM219R60G226:

Within

±12.5%

GRM155R60G475, GRM155R60E106, GRM188R60G226:

Within

±15%

GRM Series Specifications and Test Methods (2) (Note 1)-Typical Inspection

Temperature

Step

100 to 120

°C

170 to 200

°C

Time

1 min.

Step

Min.

Operating

Temp. +0/–3

±3

Room

Temp.

2 to 3

Max.

Operating

Temp. +3/–0

±3

Room

Temp.

2 to 3

Temp. (

°C)

Time (min.)

Continued on the following page.

Immerse the capacitor in a solution of ethanol (JIS-K-8101) and

rosin (JIS-K-5902) (25% rosin in weight proportion).

Preheat at 80 to 120

°C for 10 to 30 seconds.

After preheating, immerse in a eutectic solder solution for

±0.5 seconds at 230±5°C or Sn-3.0Ag-0.5Cu solder solution

for 2

±0.5 seconds at 245±5°C.

Solderability of

Termination

75% of the terminations is to be soldered evenly and

continuously.

Solder the capacitor on the test jig (glass epoxy board) shown

in Fig. 2a using a eutectic solder. Then apply a force in the

direction shown in Fig. 3a for 5

±1 sec. The soldering should be

done by the reflow method and should be conducted with care

so that the soldering is uniform and free of defects such as heat

shock.

Fig. 2a

(in mm)

Deflection

Appearance

No marking defects

Capacitance

Change

Within

±10%

Fig.3a

Type

0.2

0.3

0.4

1.0

1.2

2.2

3.5

4.5

0.56

0.9

1.5

3.0

4.0

5.0

7.0

8.0

0.23

0.3

0.5

1.2

1.65

2.0

2.9

3.7

5.6

GRM02

GRM03

GRM15

GRM18

GRM21

GRM31

GRM32

GRM43

GRM55

Capacitance meter

Flexure :

R230

Pressurizing

speed: 1.0mm/sec.

Pressurize

100

t: 1.6mm

(GRM02/03/15: t: 0.8mm)

ø4.5

No.

Test Method

Specifications

Item

GRM Series Specifications and Test Methods (2) (Note 1)-Typical Inspection

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

(Note 1) These Specifications and Test Methods indicate typical inspection.

Please refer to individual specifications (our product specifications or the approval sheet).

When no "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).

When "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 61 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 61 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL