MB95F613K datasheet(68/110 Pages) CYPRESS

68 / 110 page

Document Number: 002-04698 Rev. *A

Page 68 of 110

PRELIMINARY

MB95610H Series

15.8.3 Port G registers

■ Port G register functions

■ Correspondence between registers and pins for port G

15.8.4 Port G operations

■ Operation as an output port

❐ A pin becomes an output port if the bit in the DDRG register corresponding to that pin is set to “1”.

❐ For a pin shared with other peripheral functions, disable the output of such peripheral functions.

❐ When a pin is used as an output port, it outputs the value of the PDRG register to external pins.

❐ If data is written to the PDRG register, the value is stored in the output latch and is output to the pin set as an output port as it is.

❐ Reading the PDRG register returns the PDRG register value.

■ Operation as an input port

❐ A pin becomes an input port if the bit in the DDRG register corresponding to that pin is set to “0”.

❐ For a pin shared with other peripheral functions, disable the output of such peripheral functions.

❐ If data is written to the PDRG register, the value is stored in the output latch but is not output to the pin set as an input port.

❐ Reading the PDRG register returns the pin value. However, if the read-modify-write (RMW) type of instruction is used to read the

PDRG register, the PDRG register value is returned.

■ Operation as a peripheral function input pin

❐ To set a pin as an input port, set the bit in the DDRG register corresponding to the input pin of a peripheral function to “0”.

❐ Reading the PDRG register returns the pin value, regardless of whether the peripheral function uses that pin as its input pin.

However, if the read-modify-write (RMW) type of instruction is used to read the PDRG register, the PDRG register value is returned.

■ Operation at reset

If the CPU is reset, all bits in the DDRG register are initialized to “0” and port input is enabled.

■ Operation in stop mode and watch mode

❐ If the pin state setting bit in the standby control register (STBC:SPL) is set to “1” and the device transits to stop mode or watch

mode, the pin is compulsorily made to enter the high impedance state regardless of the DDRG register value. The input of that

pin is locked to “L” level and blocked in order to prevent leaks due to input open.

❐ If the pin state setting bit is “0”, the state of the port I/O or that of the peripheral function I/O remains unchanged and the output

level is maintained.

■ Operation of the pull-up register

Setting the bit in the PULG register to “1” makes the pull-up resistor be internally connected to the pin. When the pin output is “L” level,

the pull-up resistor is disconnected regardless of the value of the PULG register.

abbreviation

Data

Read

Read by read-modify-write

(RMW) instruction

Write

PDRG

Pin state is “L” level.

PDRG value is “0”.

As output port, outputs “L” level.

Pin state is “H” level.

PDRG value is “1”.

As output port, outputs “H” level.

DDRG

Port input enabled

Port output enabled

PULG

Pull-up disabled

Pull-up enabled

Correspondence between related register bits and pins

Pin name

PG2

PG1

PDRG

----

bit2

bit1

DDRG

PULG

MB95F613K Datasheet(PDF) 68 Page - Cypress Semiconductor

MB95F613K Datasheet(HTML) 68 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL