GRM552B11H102KA01D datasheet(119/221 Pages) MURATA

119 / 221 page

Continued on the following page.

The capacitor should be set for 24

±2 hours at room

temperature after one hour of heat treatment at 150+0/–10

°C,

then measure for the initial measurement. Fix the capacitor to

the supporting jig in the same manner and under the same

conditions as (11) and conduct the five cycles according to the

temperatures and time shown in the following table. Set it for

±4 hours at room temperature, then measure.

Temperature

Sudden

Change

Appearance

No defects or abnormalities.

Capacitance

Change

R6 : Within

±7.5%

D.F.

R6 : 0.1 max.

I.R.

More than 50

Ω · F

Dielectric

Strength

No defects

Ramp frequency from 10 to 55Hz then return to 10Hz all within

1 minute. Amplitude: 1.5 mm (0.06 inch) max. total excursion.

Apply this motion for a period of 2 hours in each of 3 mutually

perpendicular directions (total 6 hours).

Vibration

Resistance

Appearance

No defects or abnormalities.

Capacitance

Within the specified tolerance.

D.F.

R6 : 0.1 max.

MIL-STD-883 Method 2011 Condition D

Mount the capacitor on a gold metallized alumina substrate with

Au-Sn (80/20) and bond a 25

µm (0.001 inch) gold wire to the

capacitor terminal using an ultrasonic ball bond. Then, pull wire.

Mechanical

Strength

Bond

Strength

Pull force : 0.03N min.

The capacitance change should be measured after 5 min. at

each specified temp. stage.

The ranges of capacitance change compared with the

Reference Temperature value over the temperature ranges

shown in the table should be within the specified ranges.*

*Initial measurement for high dielectric constant type

Perform a heat treatment at 150 +0/–10

°C for one hour and

then let sit for 24

±2 hours at room temperature.

Perform the initial measurement.

Capacitance

Temperature

Characteristics

No bias

R6 : Within

±15% (–55°C to +85°C)

Die Shear

Strength

Die Shear force : 2N min.

MIL-STD-883 Method 2019

Mount the capacitor on a gold metallized alumina substrate

with Au-Sn (80/20). Apply the force parallel to the substrate.

Dissipation

Factor (D.F.)

R6 : 0.1 max.

The capacitance/D.F. should be measured at reference

temperature at the frequency and voltage shown in the table.

Capacitance

Within the specified tolerance.

The insulation resistance should be measured with a DC

voltage not exceeding the rated voltage at normal temperature

and humidity and within 1 minutes of charging.

Insulation

Resistance

More than 50

Ω · F

No failure should be observed when 250% of the rated voltage

is applied between the terminations for 1 to 5 seconds, provid-

ed the charge/discharge current is less than 50mA.

Dielectric Strength

No defects or abnormalities.

Using calipers.

Dimensions

Within the specified dimensions.

Visual inspection.

Appearance

No defects or abnormalities.

The rated voltage is defined as the maximum voltage that may

be applied continuously to the capacitor.

When AC voltage is superimposed on DC voltage, VP-P or VO-P,

whichever is larger, should be maintained within the rated volt-

age range.

Rated Voltage

See the previous pages.

Reference Temperature : 25

°C

Operating

Temperature

Range

R6 : –55

°C to 85°C

Mounting for testing: The capacitors should be mounted on the substrate as shown below using die bonding and wire bonding when tests No. 11 to 14 are performed.

GMA Series Specifications and Test Methods (2)

No.

Test Method

Specifications

Item

Step

Temp. (

°C)

Time (min.)

Min.

Operating

Temp.+0/–3

±3

Room

Temp.

2 to 3

Max.

Operating

Temp. +3/–0

±3

Room

Temp.

2 to 3

Step

Temperature (

°C)

±2

–55

±3

±2

±3

Capacitance

Frequency

±0.1kHz

Voltage

0.5

±0.1Vrms

V10µF (6.3Vmax.)

!Note 1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.

0. Please check with our sales representatives or product engineers before ordering.

2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product

0. specifications before ordering.

GMA Series Specifications and Test Methods (2)

117

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

When no "*" is added in PNs table, please refer to GMA Series Specifications and Test Methods (1).

When "*" is added in PNs table, please refer to GMA Series Specifications and Test Methods (2).

• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our

sales representatives or product engineers before ordering.

• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

!Note

C02E.pdf

10.12.20

GRM552B11H102KA01D Datasheet(PDF) 119 Page - Murata Manufacturing Co., Ltd.

GRM552B11H102KA01D Datasheet(HTML) 119 Page - Murata Manufacturing Co., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL