ADS8699IPWR datasheet(39/74 Pages) TI2

39 / 74 page

7.4.2.1 RESET State

The device features an active-low RST pin that is an asynchronous digital input. In order to enter a RESET state,

the RST pin must be pulled low and kept low for the twl_RST duration (as specified in the Timing Requirements:

Asynchronous Reset table).

The device features two different types of reset functions: an application reset or a power-on reset (POR). The

functionality of the RST pin is determined by the state of the RSTn_APP bit in the RST_PWRCTL_REG register.

• In order to configure the RST pin to issue an application reset, the RSTn_APP bit in the RST_PWRCTL_REG

section) are reset to their default values, the RVS pins remain low, and the SDO-x pins are tri-stated.

• The default configuration for the RST pin is to issue a power-on reset when pulled to a low level. The

RSTn_APP bit is set to 0b in this state. When a POR is issued, all internal circuitry of the device (including

the PGA, ADC driver, and voltage reference) are reset. When the device comes out of the POR state, the

tD_RST_POR time duration must be allowed for (see the Timing Requirements: Asynchronous Reset table) in

order for the internal circuitry to accurately settle.

In order to exit any of the RESET states, the RST pin must be pulled high with CONVST/CS and SCLK held low.

After a delay of tD_RST_POR or tD_RST_APP (see the Timing Requirements: Asynchronous Reset table), the device

enters ACQ state and the RVS pin goes high.

To operate the device in any of the other two states (ACQ or CONV), the RST pin must be held high. With the

RST pin held high, transitions on the CONVST/CS pin determine the functional state of the device. A typical

conversion cycle is illustrated in Figure 6-1.

7.4.2.2 ACQ State

In ACQ state, the device acquires the analog input signal. The device enters ACQ state on power-up, after any

asynchronous reset, or after the end of every conversion.

The falling edge of the RST falling edge takes the device from an ACQ state to a RESET state. A rising edge of

the CONVST/CS signal takes the device from ACQ state to a CONV state.

The device offers a low-power NAP mode to reduce power consumption in the ACQ state; see the NAP Mode

section for more details on NAP mode.

7.4.2.3 CONV State

The device moves from ACQ state to CONV state on the rising edge of the CONVST/CS signal. The conversion

process uses an internal clock and the device ignores any further transitions on the CONVST/CS signal until the

ongoing conversion is complete (that is, during the time interval of tconv).

At the end of conversion, the device enters ACQ state. The cycle time for the device is given by Equation 1:

cycle-min

conv

acq-min

(1)

Note

The conversion time, tconv, can vary within the specified limits of tconv_min and tconv_max (as specified in

the Timing Requirements: Conversion Cycle table). After initiating a conversion, the host controller

must monitor for a low-to-high transition on the RVS pin or wait for the tconv_max duration to elapse

before initiating a new operation (data transfer or conversion). If RVS is not monitored, substitute tconv

in Equation 1 with tconv_max.

www.ti.com

ADS8691, ADS8695, ADS8699

SBAS777B – DECEMBER 2016 – REVISED MARCH 2021

Submit Document Feedback

Product Folder Links: ADS8691 ADS8695 ADS8699

ADS8699IPWR Datasheet(PDF) 39 Page - Texas Instruments

ADS8699IPWR Datasheet(HTML) 39 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

Datasheet Download

Link URL