TMP89FS60 datasheet(281/410 Pages) TOSHIBA

281 / 410 page

Page 267

TMP89FS60

RA001

Note 1: Don't set I2C0AR<SA> to "0x00". If it is set to "0x00", the slave address is deemed to be matched when the I2C bus stan-

dard start byte ("0x01") is received in the slave mode.

Note 2: Don't change the contents of the registers when the start condition is generated, the stop condition is generated or the

data transfer is in progress. Write data to the registers before the start condition is generated or during the period from

when an interrupt request is generated for stopping the data transfer until it is released.

Note 3: After a software reset is generated, all the bits of the SBI0CR2 register except SBI0CR2<SBIM> and the SBI0CR1,

I2C0AR and SBI0SR2 registers are initialized.

Note 4: When the operation is switched to STOP, IDLE0 or SLOW mode, the SBI0CR2 register, except SBI0CR2<SBIM>, and the

SBI0CR1, I2C0AR and SBI0DBR registers are initialized.

Note 1: Write the transmit data beginning with the most significant bit (bit 7).

Note 2: SBI0DBR has individual writing and reading buffers, and written data cannot be read out. Therefore, SBI0DBR must not

be accessed by using a read-modify-write instruction, such as a bit operation.

Note 3: Don't change the contents of the registers when the start condition is generated, the stop condition is generated or the

data transfer is in progress. Write data to the registers before the start condition is generated or during the period from

when an interrupt request is generated for stopping the data transfer until it is released.

Note 4: To set SBI0CR2<PIN> to "1" by writing the dummy data to SBI0DBR, write 0x00. Writing any data other than 0x00 causes

an improper value in the subsequently received data.

Note 5: When the operation is switched to STOP, IDLE0 or SLOW mode, the SBI0CR2 register, except SBI0CR2<SBIM>, and the

SBI0CR1, I2C0AR and SBI0DBR registers are initialized.

18.4 Functions

18.4.1 Low Power Consumption Function

The serial bus interface has a low power consumption register (POFFCR1) that saves power when the serial

bus interface is not being used.

Setting POFFCR1<SBI0EN> to "0" disables the basic clock supply to the serial bus interface to save power.

Note that this makes the serial bus interface unusable. Setting POFFCR1<SBI0EN> to "1" enables the basic

clock supply to the serial bus interface and makes external interrupts usable.

After reset, POFFCR1<SBI0EN> is initialized to "0", and this makes the serial bus interface unusable. When

using the serial bus interface for the first time, be sure to set POFFCR1<SBI0EN> to "1" in the initial setting of

the program (before the serial bus interface control registers are operated).

Do not change POFFCR1<SBI0EN> to "0" during the serial bus interface operation, otherwise serial bus

interface may operate unexpectedly.

I2C bus address register

I2C0AR

(0x0024)

76543

210

Bit Symbol

SA0

ALS

Read/Write

R/W

After reset

00000

000

Slave address setting

Slave address in the slave mode

ALS

Communication format selection

0: I2C bus mode

1: Free data format

Serial bus interface data buffer register

SBI0DBR

(0x0025)

76543

210

Bit Symbol

SBI0DBR

Read/Write

R/W

After reset

00000

000

TMP89FS60 Datasheet(PDF) 281 Page - Toshiba Semiconductor

TMP89FS60 Datasheet(HTML) 281 Page - Toshiba Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL