26HS01GTAM03 datasheet(153/166 Pages) INFINEON

153 / 166 page

Datasheet

153 of 166

002-12337 Rev. *Y

2022-01-18

256Mb/512Mb/1Gb SEMPER™ Flash

HYPERBUS™ interface, 1.8V/3.0V

Device identification

120h

(SA) + 90h

JEDEC basic flash

parameter

DWORD-9

00h

Erase type 3 not supported

121h

FFh

Erase type 3 instruction

122h

(SA) + 91h

12h

4 Size, 256KB erase instruction = Erase type size = 2^N (where N= 18) = 12h

123h

DCh

Erase type 4 instruction = DCh

124h

(SA) + 92h

JEDEC basic flash

parameter

DWORD-10

23h

Bits 31:30 = Erase type 4 Erase, Typical time units (00b: 1 ms, 01b: 16 ms, 10b: 128 ms,

11b: 1 s) = 128 ms

= 10b

Bits 29:25 = Erase type 4 Erase, Typical time count = 00101b (typ erase time = count

+1 * units = 6 * 128 ms

= 768 ms)

Bits 24:23 = Erase type 3 Erase, Typical time units (00b: 1 ms, 01b: 16 ms, 10b: 128 ms,

11b: 1 s) = 1S = 11b (RFU)

Bits 22:18 = Erase type 3 Erase, Typical time count = 11111b (RFU)

Bits 17:16 = Erase type 2 Erase, Typical time units (00b: 1 ms, 01b: 16 ms, 10b: 128 ms,

11b: 1 s) = 1S = 11b (RFU)

Bits 15:11 = Erase type 2 Erase, Typical time count = 11111b (RFU)

Bits 10:9 = Erase type 1 Erase, Typical time units (00b: 1 ms, 01b: 16 ms, 10b: 128 ms,

11b: 1 s) = 16ms = 01b

Bits 8:4 = Erase type 1 Erase, Typical time count = 00010b (typ erase time = count +1 *

units = 3 * 16 ms

= 48 ms)

Bits 3:0 = Count = (Max Erase time / (2 * Typical Erase time)) - 1 = 0011b

125h

FAh

126h

(SA) + 93h

FFh

127h

8Bh

128h

(SA) + 94h

JEDEC basic flash

parameter

DWORD-11

82h

Bits 31 = Reserved = 1b

Bits 30:29 = Chip Erase Typical time units (00b: 16 ms, 01b: 256 ms, 10b: 4 s, 11b: 64 s)

= 11b (256M, 512M, and 1G)

Bits 28:24 = Chip Erase Typical time count = 00001b (256M), 00011b (512M), and

00110b (1G)

Bits 23:19 = Byte Program Typical Time, additional byte = 11111b

Bits 18:14 = Byte Program Typical Time, first byte = 11111b

Bits 13 = Page Program Typical Time unit (0: 8 μs, 1: 64 μs) = 64 μs = 1b

Bits 12:8 = Page Program Typical Time Count = 00111 (typ Program time = count +1 *

units = 8 * 64 μs

= 512 μs)

Bits 7:4 = Page Size (256B) = 2^N bytes = 1000h

Bits 3:0 = Count = [Max page program time / (2 * Typical page program time)] - 1 =

0010b

129h

E7h

12Ah

(SA) + 95h

FFh

12Bh

E1h for 256M

E3h for 512M

E6h for 1G

12Ch

(SA) + 96h

JEDEC basic flash

parameter

DWORD-12

ECh

Bit 31 = Suspend and Resume supported = 0b

Bits 30:29 = Suspend in-progress erase max latency units (00b: 128ns, 01b: 1μs, 10b:

8μs, 11b: 64μs)

= 8 μs = 10b

Bits 28:24 = Suspend in-progress erase max latency count = 01001b, max erase

suspend latency

= count +1 * units = 10 * 8 μs = 80 μs

Bits 23:20 = Erase resume to suspend interval count = 0001b, interval = count +1 * 64

μs = 2 * 64 μs

= 128 μs

Bits 19:18 = Suspend in-progress program max latency units (00b: 128ns, 01b: 1μs,

10b: 8μs, 11b: 64μs)

= 8 μs = 10b

Bits 17:13 = Suspend in-progress program max latency count = 01001b, max program

suspend latency

= count +1 * units = 10 * 8 μs = 80 μs

Bits 12:9 = Program resume to suspend interval count = 0001b, interval = count +1 *

64 μs = 2 * 64 μs

= 128 μs

Bit 8 = Reserved = 1b

Bits 7:4 = Prohibited operations during erase suspend

= xxx0b: May not initiate a new erase anywhere (erase nesting not permitted)

+ xx1xb: May not initiate a page program in the erase suspended sector size

+ x1xxb: May not initiate a read in the erase suspended sector size

+ 1xxxb: The erase and program restrictions in bits 5:4 are sufficient

= 1110b

Bits 3:0 = Prohibited Operations During Program Suspend

= xxx0b: May not initiate a new erase anywhere (erase nesting not permitted)

+ xx0xb: May not initiate a new page program anywhere (program nesting not

permitted)

+ x1xxb: May not initiate a read in the program suspended page size

+ 1xxxb: The erase and program restrictions in bits 1:0 are sufficient

= 1100b

12Dh

23h

12Eh

(SA) + 97h

19h

12Fh

49h

130h

(SA) + 98h

JEDEC basic flash

parameter

DWORD-13

7Ah

Bits 31:24 = Erase Suspend Instruction = B0h

Bits 23:16 = Erase Resume Instruction = 7Ah

Bits 15:8 = Program Suspend Instruction = B0h

Bits 7:0 = Program Resume Instruction = 7Ah

131h

B0h

132h

(SA) + 99h

7Ah

133h

B0h

Table 131

JEDEC SFDP Rev D parameter table (Continued)

Byte

address

(x1 SPI)

Word address

(x8 HB)

SFDP DWORD

name

Data

Description

26HS01GTAM03 Datasheet(PDF) 153 Page - Infineon Technologies AG

26HS01GTAM03 Datasheet(HTML) 153 Page - Infineon Technologies AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL